manualshive.com logo in svg

Aopos AS260, User Manual, Page: 27 / 85

Share
Download
Aopos AS260 User Manual Download Page 27

17 

 

    SETUP

Option barcode 

Option 

Alpha. entry 

Wireless network topology for handheld unit 

 

Point coordination 
Distributed coordination 

00* 
01 

Handheld unit RF channel No. 

 

02-16 
 

02-16 
06* 

Handheld unit ID 

 

01-16 
 

01-16 
01* 

Radio power level for handheld unit 

 

10dbm 
7dbm 
5dbm 
0dbm 
-5dbm 
-10dbm 
-15dbm 

01* 
02 
03 
04 
05 
06 
07 

Frequency hopping 

 

Disable 
Enable 

00 
01* 

Batch data mode 

 

 

Disable 
Out-of-range batch 
Standard batch 

00* 
01 
02 

Beep on reconnect attempt 

 

Disable 
Enable 

00* 
01 

Radio connection checking interval 

 

00-ffH (second) 
 

00-ffH 
03* 

Save data at low-battery or power-off 

 

Disable 
Enable 

00* 
01 

Low battery indicator 

 

Disable 
Enable 

00 
01* 

Enter sleeping mode interval 

 

00-ffH (minute) 
 

00-ffH 
0f* 

Enter transmitting data mode interval 

 

00-ffH (minute) 
 

00-ffH 
0f* 

VALID/INVALID/LOCK/UNLOCK protocol 

 

Disable 
Enable 

00 
01* 

Waiting for command packet interval 

 

Always 
01-99(100ms) 

00* 
01-99 

    END

Enter batch mode 

 

Send batch data 

 

Show channel information of handheld unit

※

 

Summary of Contents for AS260






















































































Reviews:

No comments