Anviz DAC844 User Manual Download Page 2 | Manualshive

Page: 2 / 50

Anviz DAC844 User Manual Download Page 2

AIM-DAC System

2

Anviz Global Inc

Notice and Disclaimer

This manual’s sole purpose is to assist installers and/or users in the safe and efficient
installation and usage of the system and/or product, and/or software described herein.

BEFORE ATTEMPTING TO INSTALL AND/OR USE THE SYSTEM, THE INSTALLER AND THE
USER MUST READ THIS MANUAL AND BECOME FAMILIAR WITH ALL SAFETY REQUIREMENTS
AND OPERATING PROCEDURES.

1

The system must not be used for purposes other than those for which it was designed.

2

The use of the software associated with the system and/or product, if applicable, is subject
to the terms of the license provided as part of the purchase documents.

3

Anviz global.Inc and/or its related companies and/or subsidiaries’ (hereafter: "Anviz")
exclusive warranty and liability is limited to the warranty and liability statement provided in
an appendix at the end of this document.

4

This manual describes the maximum configuration of the system with the maximum
number of functions, including future options. Therefore, not all functions described in this
manual may be available in the specific system and/or product configuration you
purchased.

5

Incorrect operation or installation, or failure of the user to effectively maintain the system,
relieves the manufacturer (and seller) from all or any responsibility for consequent
non-compliance, damage, or injury.

6

The text, images and graphics contained in the manual are for the purpose of illustration
and reference only.

In no event shall manufacturer be liable for any special, direct, indirect, incidental,
consequential, exemplary, or punitive damages (including, without limitation, any and all
damages from business interruption, loss of profits or revenue, cost of capital or loss of use
of any property or capital or injury).

7

All graphics in this manual are for reference only, some deviation between the image(s)
and the actual product may occur.

8

All wiring diagrams are intended for reference only, the photograph or graphic of the PCB(s)
are intended for clearer illustration and understanding of the product and may differ from
the actual PCB(s).

«
1
2
3
4
...
»

Summary of Contents for DAC844



















































Reviews:

No comments