ANthony AST-1500 Installation Manual Download Page 30 | Manualshive

Page: 30 / 36

background image

Anthony Lifgtates, Inc.

30

AST, AST-L, and AST-PLUS Models

www.anthonyliftgates.com

800-482-0003

11

— A-131036 (a

ttached to power cable)

12

— A-131001 (a

ttached to control cable)

10 AMP FUSE & HOLDER

Protects against dead shorts
in this "control circuit".
If blown, pull "fuse holder
cap", replace fuse, replace
"cap". If fuse continues to
blow, contact a qualified
mechanic, "control circuit"
may be damaged.

A-131001

10 AMP

FUSE & HOLDER

Protects against dead shorts

in this "control circuit".

If blown, pull "fuse holder

cap", replace fuse, replace

"cap". If fuse continues to

blow, contact a qualified

mechanic, "control circuit"

may be damaged.

13

— A-131125 (a

ttached only to galvanized

liftgates)

Welding on galvanized and stainless
steel parts gives off especially
hazardous fumes.

• Remove galvanizing from area to weld.
• Provide good ventilation.
• Wear suitable respirator.

A-131125

«
...
28
29
30
31
32
...
»

Summary of Contents for AST-1500





































Reviews:

No comments

Related manuals for AST-1500

Brand: Vectaire Pages: 2

Brand: ATD Tools Pages: 24

Brand: KAPTARLIFT Pages: 16

Brand: M-system Pages: 19

Brand: Cruz Pages: 12

Brand: Campbell Hausfeld Pages: 48

Brand: HALDER Pages: 2

ControlLogix 1756-CNB

Brand: Allen-Bradley Pages: 36

Brand: M-system Pages: 7

Brand: GYS Pages: 9

Brand: Favero Pages: 27

Brand: Balboa Instruments Pages: 76

Multilin DGT Series

Brand: GE Pages: 60

Brand: STAMOS Pages: 7

Brand: THORLABS Pages: 81

Brand: HiGH-LiFT Pages: 29

EASYHEAT PSR1006

Brand: Emerson Pages: 5

Keystone OM1 - EPI2

Brand: Emerson Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands