manualshive.com logo in svg

ANthony AST-1500, Installation Manual, Page: 24 / 36

Share
Download
ANthony AST-1500 Installation Manual Download Page 24

Anthony Lifgtates, Inc. 

 

24 

AST, AST-L, and AST-PLUS Models

www.anthonyliftgates.com 

 

800-482-0003

4.5  Cut-Off Solenoid Connection

7KHLQVWDOODWLRQRIDFXWRႇVROHQRLGLVDUHFRPPHQGHG
RSWLRQIRUDOO9ROWHOHFWULFOLIWJDWHV,QVWDOOLQJDFXWRႇ

solenoid will help to prevent accidental or unauthorized 
use of the liftgate.

7KHRSWLRQDO$&XW2ႇ6ROHQRLG.LWFDQEHXVHG

in any truck, but is essential for tilt cab applications, as it 
requires only a lightweight wire running to the cab, not a 

ODUJHFDEOHDVUHTXLUHGE\WKHFXWRႇVZLWFK

Follow the directions on the installation instruction sheet 
that comes with the kit.

Cut-Off Solenoid Installed Between Battery and Fuse Assembly. 
(2)  Short cable, part of solenoid kit.  (1) Long length of power cable 
leading to power unit.

+

–

Ground

A-1018

Long

Power

Cable

Short

Power

Cable

Short

Power 

Cable

Fuse

Vehicle

Battery

Ground

Cut-Off

Solenoid

Fuse Box

On/Off

Toggle Switch

Liftgate

Solenoid

Wiring Diagram with Cut-Off Solenoid.

4.6  Cut-Off Switch Connection

7KHLQVWDOODWLRQRIDFXWRႇVZLWFKLVDOVRDUHFRPPHQGHG
RSWLRQIRUDOO9ROWHOHFWULFOLIWJDWHV,QVWDOOLQJDFXWRႇ

switch will help to prevent accidental or unauthorized use 
of the liftgate.

 Follow the installation directions on the installation 
instruction sheet that comes with the kit.

Cut-Off Switch Mounted in Cab of Truck.

A-1019

+

–

Long

Power

Cable

Fuse

Ground

Vehicle

Battery

Cab

Mounted

Cut-Off

Switch

Short

Power

Cable

Short

Power

Cable

Liftgate

Solenoid

Wiring Diagram With Cab Cut-Off Switch.

Summary of Contents for AST-1500





































Reviews:

No comments