3
♦
If the supply cord is damaged, it must be replaced by manufacturer or its service agent or similarly qualified
personnel in order to avoid a hazard.
♦
The output nozzle becomes very hot during operation (300°C). Keep flammable materials at least 50 cm away
from the nozzle.
♦
Always allow your ANTARI Fog Machine to cool down before attempting to clean or service it.
Danger of Explosion
♦
Never add flammable liquids of any kind (such as oil, gas, perfume) to the fog liquid.
♦
Use only high-quality, water-based fog liquid that your dealer recommends. Other fog liquids may cause
clogging or “spitting”.
♦
Always make sure there is sufficient liquid in the tank. Operating this unit without liquid will cause damage to
the pump as well as over-heating of the heater.
♦
If your ANTARI Z-1500II or Z-3000II Fog Machine fails to work properly, discontinue use immediately. Drain all
fog liquid from the tank, pack the unit securely (preferably in the original packing material), and return it to your
ANTARI dealer for service.
♦
Always drain tank before mailing or transporting this unit.
♦
Never drink fog liquid. If it is ingested, call a doctor immediately. If fog liquid comes in contact with skin or
eyes, rinse thoroughly with water.
Note:
Pay attention to all warning labels and instructions printed on the exterior of your ANTARI Fog Machine
Unpacking & Inspection
Open the shipping carton and verify that all equipment necessary to operate the system has arrived intact. The
shipping carton should contain the following items:
1. One unit of One unit of Z-Series II Fog Machine
2. Power
cord
3. Z-20 multi-function remote control with attached cord
4. User
Manual
If any equipment is missing contact your ANTARI dealer immediately.
Before beginning your initial setup on ANTARI Z-1500II or Z-3000II Fog Machine, make sure that there is no
evident damage caused by transportation. In the event that the unit’s housing or cable is damaged, do not plug it
in and do not attempt to use it until after contacting your ANTARI dealer for assistance.
Setup
♦
Remove all packing materials from shipping box. Check that all foam and plastic padding is removed,
especially in the nozzle area.
♦
Place fog machine on a flat surface and remove fog liquid tank cap.
♦
Fill with ANTARI fog liquid or other high-quality water-based fog fluid recommended by ANTARI dealer. Any
other types of fluid can damage the unit resulting in spitting and serious clogging problem. When filled, place
cap back on liquid tank. Be careful not to exceed the maximum fluid level. DO NOT OVERFILL.
♦
Firmly attach the Z-20 control module cable to the connector inside the rear chamber of the machine.
Operation
♦
Add fluid carefully to the liquid tank. Do not overfill the tank.
♦
The Plug should be in a position that is accessible when using the machine.
♦
Plug power cord into a grounded electrical outlet. Turn the power switch to “
ON
” on the back of the machine.
Warm-up is completed when the display on the control module shows
“Ready to Fog”
♦
To emit fog press the appropriate button on the control module for the desired length of time.
♦
The control unit display will display “Warming up” and “Ready to fog” as the machine re-heats to the proper
operating temerature.
4
♦
For further information on operating your Z-1500II, Z-3000II Fog Machine, see the section titled “
Remote
Control Operation
”.
CAUTION:
“Visibility during operation is reduced”
This model can be operated at a floor level or sitting on any regular surface. Whatever installation method you
choose, do not allow the unit to have more than 15 degree angle of inclination.
Important:
Always monitor tank fluid level as you are fogging. Running a fog machine with no fluid can
permanently damage the unit.
If your model includes a mounting bracket designed for overhead installation, it may be installed floor
level or suspended overhead. If the unit is to be mounted using the bracket, it is important that the fog
does not shoot directly at any one’s face. Whatever installation method you choose, do not allow the
unit to have more than a 15 degree angle or onclination.
Note:
A fluid level sensor is installed on the unit. The machine will stop to fog if the fluid is lower than the
maximum level.
If you experience low output, pump noise or no output at all, unplug immediately. Check fluid level, the
external fuse, remote control connection and power from the wall. If all of the above appears to be O.K.,
plug the unit again. If fog does not come out after holding the remote button down for 30 seconds, check the
hose attached to the tank to make sure there is fluid going through the hose. If you are unable to determine
the cause of the problem, do not simply continue pushing the remote button, as this may damage the unit.
Return the machine to your ANTARI dealer.
Specifications
Model Number
Z-1500II
Z-3000II
Power Supply
AC100-120V, AC230/ 50HZ-60HZ
AC100-120V, AC230/ 50HZ-60HZ
Power Consumption
1500 W
3000 W
Output Volume
ca. 700 m³/min.
ca. 1400 m³/min.
Tank Capacity
6 Liter
6 Liter
Fluid Consumption
12 min./Liter
5 min./Liter
Weight
14 Kg
20 Kg
Dimensions(mm)
L 688 W 285 H188
L 735 W 310 H 192
Remote Included
Z-20 Z-20
Optional Remote
Z-30 Z-30
Control Module Operation
♦
Z-20:
A 10 meter wired multi-function remote control with 5-pin XLR connector for ANTARI Fog Machine
models Z-1500II and Z-3000II. Its interface allows the operator to customize fog machine functions by
adjusting fogging duration, interval and volume. Its LCD displays current operating parameters, which are
automatically stored in non-volatile memory, allowing the machine to be powered down without losing function
settings.
