Anolis ArcSource 96 Integral, User Manual

Page: 18 / 28

ArcSource 96 Integral (RGBW)
18
Synchronous operation of multiple fixtures requires that they must be connected on a data link and one of them is
set as a master (“MASt“) and the rest as the slaves (“SLA“). Up to 32 fixtures can be connected in a master/slave
chain. Only one fixture can be set as the master. This option does not function at wireless operation.
Note: Disconnect the fixtures from the DMX controller before master/slave operating, otherwise data collisions can
occur and the fixtures will not work properly. See the chapters “Stand-alone operation“ and “ Master/slave
connection“.
Auto. --- Automatic playback . This function allows you to select the program which will be played after switching
the fixture on. Selected program will be played continuously in a loop.
1. Use the UP/DOWN buttons to find “ St.AL. “ menu.
2. Press the ENTER button.
3. Use the UP/DOWN buttons to select “ Auto “ item.
4. Press the ENTER button.
5. Use the UP/DOWN buttons to select desired program.
6. Press the ENTER button to confirm the choice.
PLAY --- Playing program . By enter to this menu a complete overview of all programs is offered, from which the
program to be run can be selected.
1. Use the UP/DOWN buttons to find “ St.AL. “ menu.
2. Press the ENTER button.
3. Use the UP/DOWN buttons to select desired program.
4. Press the ENTER button. The selected program runs in a loop.
Edit --- Editing a program . The fixture offers 3 freely editable programs (EPG.1-EPG.3) each up to 68 steps. Every
program step includes a fade time-the time taken by the step´s channel status to reach the desired level and a
step time-the total time occupied by the step in the program.
E.g. If “F.tim.“=5 second and “S.tim.“=20 second, effects will go to the desired position during 5 seconds and after
that they will stay in this position for 15 seconds before going to the next prog. step
1. 1. Use the UP/DOWN buttons to find “ St.AL. “ menu and press the ENTER button.
2. Use the UP/DOWN buttons to select “ Edit “ menu and press the ENTER button.
3. Use the UP/DOWN buttons to select a program you want to edit (PrG.1-PrG.3 and press ENTER button.
4. Use the UP/DOWN buttons to select a desired program step ("St.01" - "St.68") and press ENTER button.
5. Use the UP/DOWN buttons to select a channel you want to edit and press the ENTER button.
List of editable items:
“P.End” -
a total number of the program steps (value 1-68). This value should be set before start
Programming (e.g. if you want to create program with 10 steps, set P.End=10).
“ rEd1” - red LEDs saturations-array1 (0-255)
“GrE1“ - green LEDs saturations-array1 (0-255)
“bLu1“ - blue LEDs saturations-array1 (0-255)
“Whi1“ - white LEDs saturations-array1 (0-255)
“ rEd2” - red LEDs saturations-array2 (0-255)
“GrE2“ - green LEDs saturations-array2 (0-255)
“bLu2“ - blue LEDs saturations -array2 (0-255)
“Whi2“ - white LEDs saturations-array2 (0-255)
“MACr“ - colour macros (0-255)
“Stro.“ - a strobe, shutter (0-255)
“dimr“ - a dimmer (0-255)
“F.dim“ - a fine dimmer (0-255)
“F.tim.“ - a fade time, (0-25.5) seconds
“S.tim.“ - step time, value (0-25.5) seconds
“COPY“. – this item duplicates the current prog. step to the next prog. step. The item “P.End” is increased
automatically.
6. Use the UP/DOWN buttons to set a DMX value of the channel and then press the ENTER button.