ANK DAC5.1 Signature Construction Manual Download Page 84

Page: 84 / 104

14.1

Connecting I/V to Digital Board

Figure 60 - Wiring the I/V to the Digital Board

In the above graphic you can see the Output of the Digital Board connects to the IV

transformers. The red wire from the IV is the signal input and the black and green wires are

connected to Ground. The wire from the IV transformers when you strip the ends will have

exposed wire, this wire actually needs to be TINNED as it has a coating on it and will be difficult

to solder into the board without doing this first. Once tinned, you can bring it to the hole on the

digital board and apply some solder and it will connect to the board.
For the black and green wires, we suggest you twist them together and strip off some exposed

wire, then tin this wire and place into the RGND on the digital board.

Summary of Contents for DAC5.1 Signature









































































































Search results

Summary of Contents for DAC5.1 Signature

Reviews:

Related manuals for DAC5.1 Signature

Brands by name

Popular brands

ANK DAC5.1 Signature, Construction Manual

Search results

Summary of Contents for DAC5.1 Signature

Reviews:

Related manuals for DAC5.1 Signature

Brands by name

Popular brands