ANK DAC5.1 Signature Construction Manual Download Page 57

Page: 57 / 104

10.5

Wiring the Super Regulator Board

With the board complete we will refer back to the PTDAC4-1 transformer and take the three

remaining pairs of twisted wires. It actually does not matter which pair goes to which input,

they are all 8v AC pairs at 2AMPs so you can go ahead and connect the three pairs to the three

inputs. Also it does not matter which wire of the pair goes to the two input pins as it is AC

voltage and just a phase difference. Transformer details can be found on the next page.

Figure 36 - Twisted wires from the PTDAC4-1 Transformer



Take the Blue & Blue/White pair and twist together



Take the Orange and Orange/White pair and twist together



Take the Black and Black/Green pair and twist together

Summary of Contents for DAC5.1 Signature









































































































Search results

Summary of Contents for DAC5.1 Signature

Reviews:

Related manuals for DAC5.1 Signature

Brands by name

Popular brands

ANK DAC5.1 Signature, Construction Manual

Search results

Summary of Contents for DAC5.1 Signature

Reviews:

Related manuals for DAC5.1 Signature

Brands by name

Popular brands