ANK DAC5.1 Signature Construction Manual Download Page 36

Page: 36 / 104

8.2.2

Install the 8-Pin Valve Base

Figure 21 - Installing the 8-pin Valve Base

Install the 8 pin black Valve Base first; the trick to Valve Bases is to make sure they are flat so

you don’t have a tube that will be on an angle. First of all make sure the Valve Base is keyed to

the stencil such that the notch on the valve base matches the notch on the stencil of the PCB.

This is to ensure the 8 pin Valve Base is oriented correctly. You can use some tape to secure the

Valve Base while you solder on the bottom side. You want to solder just one pin in and then

solder the pin on the opposite side of the base, this way with just two pins soldered you can

turn over to look to see the valve base is flat. If it is not for whatever reason you can heat one

of the soldered pins and push on it to make sure your base is flat. If all is good then continue

soldering the other pins.

Summary of Contents for DAC5.1 Signature









































































































Search results

Summary of Contents for DAC5.1 Signature

Reviews:

Related manuals for DAC5.1 Signature

Brands by name

Popular brands

ANK DAC5.1 Signature, Construction Manual

Search results

Summary of Contents for DAC5.1 Signature

Reviews:

Related manuals for DAC5.1 Signature

Brands by name

Popular brands