ANK DAC5.1 Signature Construction Manual Download Page 48

Page: 48 / 104

10 -

DAC5.1 Interwiring

In this section, we are going to make all the necessary connections to hook up the Power

Supply. Read through this section first before starting any work.

We will start with the Mains

transformer PTL4. This transformer supplies the high voltage to the Power Supply PCB. Start by

looking at the three pieces of documentation below that is also located in the appendix. The

Overall wiring graphic for the Power Supply and the two Mains transformers. These are also in

large format on the next three pages, you might want to print these out!

Figure 30 - DAC 5.1 Interwiring

The above documentation can be found in the next full pages ahead so you can print out along

with the Mains transformer connections!
PRINT OUT and review!

Summary of Contents for DAC5.1 Signature









































































































Search results

Summary of Contents for DAC5.1 Signature

Reviews:

Related manuals for DAC5.1 Signature

Brands by name

Popular brands

ANK DAC5.1 Signature, Construction Manual

Search results

Summary of Contents for DAC5.1 Signature

Reviews:

Related manuals for DAC5.1 Signature

Brands by name

Popular brands