ANK DAC5.1 Signature Construction Manual Download Page 60 | Manualshive

Page: 60 / 104

background image

Ok if you are feeling ready and you have checked over all your connections then you are ok to

turn on and that is with NO power supply tube installed
You should be able to get 5 voltages with no tube installed
They are as follows:
The three 9V DC voltages on the Super regulator board
The two 6.3V DC voltages on the Filament Board

Figure 38 - Voltage check locations

See the next 2 pages for a printable version of the voltage checks. Now here are the steps to

power on and test power supply
See the graphic on next page to identify these locations, use your voltmeter to measure.
If you are not getting any voltages, make sure you are on DC volts on your meter and if still no

luck check that the Power Switch is in the 1 position against chassis and that the FUSE is not

blown. You can use an ohm meter on the fuse when it is removed and see if it is zero ohms

(working) or Infinite (means fuse has blown).
If things are not working, contact

[email protected]

for the next steps. If all is well

then move on to the next step.

Turn the unit off.

56

«
...
58
59
60
61
62
...
»

Summary of Contents for DAC5.1 Signature









































































































Reviews:

No comments

Related manuals for DAC5.1 Signature

Brand: Omega Digitech Pages: 8

Brand: Kramer Pages: 15

Brand: PEAK COMMUNICATIONS Pages: 18

Brand: IONODES Pages: 23

Brand: Cobra Pages: 14

Brand: IPEX Pages: 12

Brand: GUSTARD Pages: 22

Brand: Phrontier Technologies Pages: 16

Brand: TRENDnet Pages: 1

Atlona AT-HDVS-SC-RX

Brand: Panduit Pages: 41

Brand: LINK-MI Pages: 6

Brand: Martin Audio Pages: 51

Brand: DAB Pages: 600

Brand: AXIOMATIC Pages: 44

Brand: Renaissance Learning Pages: 2

Brand: JVC Pages: 20

Brand: Dataforth Pages: 3

Brand: Transition Networks Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands