background image

5000M Crusader G Upgrade Installation Guide

 

 

P/N 70000549B 

 
 

  

 

All rights reserved. Subject to change without notice. 

18 

14-February-03 

  

 Replace the Console Rear Panel Filter, P/N 85300009 

Refer to 

Figure 7

.  

Table 2 

lists the parts shown in 

Figure 7

To replace the console fan filter:  
1.  Remove the screws that hold the frame to the rear panel of the 

console. 

2.  Replace the console filter, and reattach the frame. 

Inspect rear panel filter and verify the fan’s airflow monthly.  ANILAM 
recommends that you replace the console filter every three months.  
However, under some adverse environmental conditions, such as oil 
vapor contamination and/or high levels of particulate, more frequent filter 
changes may be required.  The suggested interval, in such cases, is once 
a month. 

Figure 7, Console Rear Panel – Inside View 

 

 

Table 2, Console Rear Panel Parts 

Item Part 

Number 

Description 

Qty. 

23000225 

Console, Rear Panel, 5000M Crusader G 

85400011 

Fan, 12VDC, 0.72 A, 105 CFM 

85400013 

Fan Finger Guard 

85300009 Filter, 

POLY-U 

21900112 

Bracket, Fan Filter, Console 

86100238 

Screw, #6-32 x 1-7/8” LG PHL PAN HD 

86100166 

Screw, #6-32 x 5/8” LG PHL PAN HD, BLK 

 

PANEL INSIDE

Summary of Contents for 5000M



















Reviews: