background image

ANEP BOX-C

Version #1

09/22//2014

7

     PROGRAMMING MODE

                    Important :

        • 

Access to the programming mode is only possible if the phone line is hung up.

           ( Beware if several modules share the same line )

        • 

The 

BOX-C

 keypad is used to program all the parameters.

        • 

To avoid unwanted modifications, the programming mode is protected by an access

           code : 

*

 1 2 3

        • 

This code may be modified by the technician ( 1 to 7 digits )

 (See page 14)

3.1 - Enter programming mode

        

Enter 

followed by the access code to enter programming mode

        

Example : using the factory default code

        

 

*

 1 2 3

        The unit plays a melody

 

        .

.. Then 2 beeps are made every 20 seconds

 

3

.1.1

 - Exit programming mode

       

        

when the unit has been programmed

 

 

Press the key

  « 

*

 »

         Finish programming, the unit plays a melody 

        Nota

If no key is pressed for over 3 minutes, the unit will automatically exit the 

        programming mode.

        The unit plays a melody 

3

Summary of Contents for BOX-C

























Reviews: