andrews LWH42 Installation Manual, Operation And Maintenance Manual Download

Page: 13 / 64

Flue Terminal Installation Precautions

Note the following flue terminal installation requirements

• Do not install the flue terminal indoors

• Install the flue terminal with a downward slope

upward

slope

downward

slope

• Install with the proper length protruding through the wall (FF-100A only)

• Avoid storing hazardous

objects near the terminal

Petrol

Gas

Proper installation. The
red line can be seen,but
the red rectangle cannot
be seen from the outside.

Flue Terminal

not far
enough

too far

Snow
drift

Tree

• Avoid installing the terminal where obstacles will block it

• Clearance from the flue terminal.
If multiple units are installed,

terminals must be separated by
300mm or more in a plain view
regardless of the vertical clearance.

Flue Terminal

300mm or more

300mm or
more

• In the case the discharge direction of the exhaust

is to the side as shown in the diagram below, do
not select the supply/exhaust tube top. Incomplete
combustion caused by short cycling of exhaust
gas may occur as a result.

(except terminal guard.)

Flue Pipe Installation

(Internal Installation Only)

Flue Terminal Installation

• Follow the installation instructions included with the flue terminal and which are reproduced at the end

of this manual. This appliance must be the flue through the wall, not vertically to the roof.

1500mm or more
(terminal above

a terminal.)

Flue Terminal

Snow
drift

(L)WH42̲56(09̲15)̲E

05.9.28, 1:31 PM

Page 9

Adobe PageMaker 6.5J/PPC

Summary of Contents for LWH42

































































Search results

Summary of Contents for LWH42

Reviews:

Related manuals for LWH42

Brands by name

Popular brands

andrews LWH42, Installation Manual, Operation And Maintenance Manual

Search results

Summary of Contents for LWH42

Reviews:

Related manuals for LWH42

Brands by name

Popular brands