andrews LWH42 Installation Manual, Operation And Maintenance Manual Download | Manualshive

Page: 38 / 64

background image

34

Compatibility Check

• Make sure that the flue terminal is compatible with the product it will be installed with. If an improper

terminal is used, a fire hazard will be created.

Choosing the Installation Site

• Maintain the proper clearances to combustibles

The heat and moisture from the water heater may cause corrosion of aluminum materials.

• Install the flue terminal so that it is easily accessible for maintenance from both the indoors and the

outdoors.

• Install the flue terminal so that all exhaust is directed to and all intake air is taken from the outdoors.
• Steam or condensed water may drip out of the flue terminal. Dispose of this condensed water

according to local codes and in order to prevent injury or property damage.

Check Wall Thickness

• This flue terminal model has four different sizes. Choose the correct model to fit the thickness of

the wall that the terminal will pass through.

Model name

Wall thickness

FF-100A-200

130 mm to 210 mm

FF-100A-400

210 mm to 370 mm

FF-100A-700

370 mm to 690 mm

15-2-2. Before Installation

Caution

(L)WH42̲56(33̲38)̲E

05.10.4, 1:41 PM

34

«
...
36
37
38
39
40
...
»

Summary of Contents for LWH42

































































Reviews:

No comments

Related manuals for LWH42

Brand: NARVI Pages: 24

Brand: Paloma Pages: 24

Brand: Park House Healthcare Pages: 28

Odyssey ODYR-25-1

Brand: Dakota Digital Pages: 8

Brand: Calpeda Pages: 72

LEADER ECOTRONIC Series

Brand: DAB PUMPS Pages: 10

Brand: Bayrol Pages: 56

Brand: Hoshizaki Pages: 10

Brand: magicpak Pages: 12

Brand: Helios Radiant Pages: 38

Brand: Dimplex Pages: 8

Brand: IDEAL Pages: 68

Brand: Royal Sovereign Pages: 16

Double Bubbler LF SCWT14CB Series

Brand: Halsey Taylor Pages: 6

Brand: BUSCH Pages: 40

Brand: Whale Pages: 64

Brand: Annovi Reverberi Pages: 14

Brand: Altech Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands