andrews LWH42 Installation Manual, Operation And Maintenance Manual Download | Manualshive

Page: 11 / 64

background image

7

6.

Installation Clearances

Before installing, check for the following:

The appliance must be installed in a suitably ventilated room, in accordance with the regulations
in force.
Install in accordance with relevant building and mechanical codes, as well as any local, state or
national regulations.

Item

Distance from combustibles

• Maintain the following clearances

from both combustible and
non-combustible materials.

• There must be a clearance of 600mm or

more in front of the flue terminal.

• This restriction will not be applied to an

area where an effective shield makes a
clearance of 600mm or more in front of
the exhaust outlet.

Check

Illustration

Caution

• If possible, leave 200mm or more on either

side of the unit to facilitate inspection.

• If possible, leave 600mm or more in front

of the unit to facilitate maintenance and
service if necessary.

Securing of space for

repair/inspection

600mm
or more

200mm
or more

Outdoor Clearances to Opening

into Any Building

Distance from
the top surface

Distance from
the side

45 mm

or more

45 mm

or more

Consult the flue
manufacturer for
clearances

300mm
or more

300mm
or more

300mm
or more

There must be no
building opening
within this area.

300mm
or more

Flue Terminal

200mm
or more

(L)WH42̲56(01̲08)̲E

05.9.28, 1:28 PM

Page 7

Adobe PageMaker 6.5J/PPC

«
...
9
10
11
12
13
...
»

Summary of Contents for LWH42

































































Reviews:

No comments

Related manuals for LWH42

Brand: Danfoss Pages: 12

Brand: A.O. Smith Pages: 65

Brand: Zoeller Pages: 12

Brand: VEAB Pages: 16

Brand: Kambrook Pages: 6

Brand: Karibu Pages: 60

Brand: SereneLife Pages: 10

Brand: VTS Medical Systems Pages: 23

Brand: AquaPRO Pages: 4

Brand: Rheem Pages: 28

Brand: Masterflex Pages: 67

Brand: Warren rupp Pages: 22

Brand: Rinnai Pages: 20

Duro Titan SBA025T1

Brand: Canature WaterGroup Pages: 8

UFLEX SilverSteer UP25 F-SVS

Brand: Ultraflex Pages: 29

Brand: Toyostove Pages: 18

Brand: Robur Pages: 36

Habitat PWF105-C

Brand: Plantronics Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands