Anaheim Automation DPC50501 User Manual Download Page 37

September 2012

L010194

37

A N A H E I M   A U T O M A T I O N

COPYRIGHT

 

Copyright 2012 by Anaheim Automation. All rights reserved. No part of this publication may be reproduced, 

transmitted, transcribed, stored in a retrieval system, or translated into any language, in any form or by 

any means, electronic, mechanical, magnetic, optical, chemical, manual, or otherwise, without the prior 

written permission of Anaheim Automation, 4985 E Landon Drive, Anaheim, CA 92807. 

DISCLAIMER

Though every effort has been made to supply complete and accurate information in this manual, the 

contents are subject to change without notice or obligation to inform the buyer. 

In no event will Anaheim 

Automation be liable for direct, indirect, special, incidental, or consequential damages arising out 

of the use or inability to use the product or documentation.

  

Anaheim Automation’s general policy does not recommend the use of its’ products in life support applications 

wherein a failure or malfunction of the product may directly threaten life or injury.  Per Anaheim Automation’s 

Terms and Conditions, the user of Anaheim Automation products in life support applications assumes all 

risks of such use and indemnifies Anaheim Automation against all damages.

LIMITED WARRANTY

All Anaheim Automation products are warranted against defects in workmanship, materials and construction, 

when used under Normal Operating Conditions and when used in accordance with specifications. This 

warranty shall be in effect for a period of twelve months from the date of purchase or eighteen months 

from the date of manufacture, whichever comes first. 

Warranty provisions may be voided if products 

are subjected to physical modifications, damage, abuse, or misuse.

Anaheim Automation will repair or replace at its’ option, any product which has been found to be defective 

and is within the warranty period, provided that the item is shipped freight prepaid, with previous authorization 

(RMA#) to Anaheim Automation’s plant in Anaheim, California. 

TECHNICAL SUPPORT

If you should require technical support or if you have problems using any of the equipment covered by this 

manual, please read the manual completely to see if it will answer the questions you have. If you need 

assistance beyond what this manual can provide, contact your Local Distributor where you purchased the 

unit, or contact the factory direct.

July 2018

Summary of Contents for DPC50501






































Reviews: