background image

L0126J  

 40 

 
ID501  System Date (yymmdd)  
ID502  System Time (hhmm)  
ID504  System Daylight Savings Mode (OFF, NA, MEX, EU, 

AUS)  

 

PA101  Product number (set to the selection number (e.g. 12) 
PA102  Product price  
PA103  Product Identification (Customer Facing product name) 
 
PA201  Number of products vended since initialization  
PA202  Value of paid products since initialization  
PA203  Number of products vended since last reset  
PA204  Value of paid product sales since last reset  
PA205  Number of discounted paid vends since initialization  
PA206  Value of discounts given since initialization  
PA207  Number of discounted paid vends since last reset  
PA208  Value of discounts given since last reset  
 
PA401  Number of free vends since initialization (not sent if = 

 0) 

 
PC101  Product number (one based index)  
PC102  Product price  
PC103 Product 

Identification 

 

SE01 

Number of Included Sets  

SE02 

Transaction Set Control  Number: “0001”  

 
TA201  Value of vend token sales since initialization  
TA202  Number of vend token vends since initialization  
TA203  Value of vend token sales since last reset  
TA204  Number of vend token sales since last reset  
 
VA101  Value of all paid sales since initialization  
VA102  Number of all paid vends since initialization  
VA103  Value of all paid sales since last reset  
VA104  Number of all paid sales since last reset  
VA105  Value of all discounts since initialization  
VA106  Number of all discounted paid vends since initialization  
VA107  Value of all discounts since last reset  
VA108  Number of all discounted paid vends since initialization  
 
VA301   Value of all free vends since initialization  
VA302   Number of all free vends since initialization  
VA303   Value of all free vends since last reset  
VA304   Number of all free vends since last reset 
 
 

 

Receiving devices should not be designed to expect any 
particular transmission order. 
 
If firmware or BOOT is upgraded, installation numbers are reset 
to zero. 
 
Certain fields are omitted if all element values are zero. 

 
 
 
 

10 SUPPORTED DEX FIELDS 

Summary of Contents for 28 Slim Gem




















































Reviews: