Amphenol Temposonics R V Analog RH5, Operation Manual, Page: 53 / 64

Temposonics
®
R-Series
V
POWERLINK
Operation Manual
I 53 I
Table 3: Index 6010, 6301, 6302, 6310, 6311, 6312, 6313, 6320, 6321, 6322, 6323, 6330, 6331, 6332, 6333
Index Subindex Name Object type Attribute Data type Description
6010
Preset values for multi-sensor devices
Array
The preset can be set for up to 30 magnets.
0 Number of entries Variable ro Unsigned8
1…30 Preset for 1…30 magnets Variable rw Integer32
6301
CAM enable register Array Via the “CAM enable register” the CAM channels can be enabled:
• Bit value 0: CAM inactive
• Bit value 1: CAM active
It can be set for up to 30 magnets.
0 Number of entries Variable ro Unsigned8
1…30 CAM enable register for 1…30 magnets Variable rw Unsigned8
6302 CAM enable polarity
Array
With “CAM enable polarity”, the polarity of each CAM can be definated.
If the polarity bit of a CAM is set, the current CAM state will be inverted.
It can be set for up to 30 magnets.
0 Number of entries Variable ro Unsigned8
1…30 CAM enable polarity for 1…30 magnets Variable rw Unsigned8
6310 CAM 1 low limit
Array
This object determines the lower limit of position for CAM 1.
It can be set for up to 30 magnets.
0 Number of entries Variable ro Unsigned8
1…30 CAM 1 low limit for 1…30 magnets Variable rw Integer32
6311 CAM 2 low limit Array This object determines the lower limit of position for CAM 2.
It can be set for up to 30 magnets.
0 Number of entries Variable ro Unsigned8
1…30 CAM 2 low limit for 1…30 magnets Variable rw Integer32
6312 CAM 3 low limit Array This object determines the lower limit of position for CAM 3.
It can be set for up to 30 magnets.
0 Number of entries Variable ro Unsigned8
1…30 CAM 3 low limit for 1…30 magnets Variable rw Integer32
6313 CAM 4 low limit Array
This object determines the lower limit of position for CAM 4.
It can be set for up to 30 magnets.
0 Number of entries Variable ro Unsigned8
1…30 CAM 4 low limit for 1…30 magnets Variable rw Integer32
6320 CAM 1 high limit Array
This object determines the upper limit of position for CAM 1.
It can be set for up to 30 magnets.
0 Number of entries Variable ro Unsigned8
1…30 CAM 1 high limit for 1…30 magnets Variable rw Integer32
6321 CAM 2 high limit Array
This object determines the upper limit of position for CAM 2.
It can be set for up to 30 magnets.
0 Number of entries Variable ro Unsigned8
1…30 CAM 2 high limit for 1…30 magnets Variable rw Integer32
6322 CAM 3 high limit Array This object determines the upper limit of position for CAM 3.
It can be set for up to 30 magnets.
0 Number of entries Variable ro Unsigned8
1…30 CAM 3 high limit for 1…30 magnets Variable rw Integer32
6323 CAM 4 high limit Array This object determines the upper limit of position for CAM 4.
It can be set for up to 30 magnets.
0 Number of entries Variable ro Unsigned8
1…30 CAM 4 high limit for 1…30 magnets Variable rw Integer32
6330 CAM 1 hysteresis Array
Via this parameter the delay setting of the switch points for CAM 1 can be
set. It can be set for up to 30 magnets.
0 Number of entries Variable ro Unsigned8
1…30 CAM 1 hysteresis for 1…30 magnets Variable rw Integer32
6331 CAM 2 hysteresis Array
Via this parameter the delay setting of the switch points for CAM 2 can be
set. It can be set for up to 30 magnets.
0 Number of entries Variable ro Unsigned8
1…30 CAM 2 hysteresis for 1…30 magnets Variable rw Integer32
6332 CAM 3 hysteresis Array Via this parameter the delay setting of the switch points for CAM 3 can be
set. It can be set for up to 30 magnets.
0 Number of entries Variable ro Unsigned8
1…30 CAM 3 hysteresis for 1…30 magnets Variable rw Integer32
6333 CAM 4 hysteresis Array Via this parameter the delay setting of the switch points for CAM 4 can be
set. It can be set for up to 30 magnets.
0 Number of entries Variable ro Unsigned8
1…30 CAM 4 hysteresis for 1…30 magnets Variable rw Integer32