background image

OPERATION 

 19

Light

The   sensor operates independently and 

using it does not affect other functions and 

settings.   sensor is inactive in a standby 

mode.

The light in the oven turns on:

- when you touch 

 — for 30 seconds;

- when you touch and hold   for 3s – until 

the appliance enters standby mode,  

when you use any heating function or a pre-

set programme — for 30s;

when "fast heat-up" completes — for 30s;

when you open the door — until the door is 

closed, but no longer than for 10 minutes.

Touch   to turn off the light at any time.

Cooling fan.

Cooling fan operates independently of the 

set functions and the appliance status. 

Cooling fan turns on when the oven cham-

ber temperature exceeds 50°C and turns off 

when it is below this temperature. 

Thermostat

Thermostat symbol (next to the oven tem-

perature) indicates the operating status of 

heaters. If any of the heating elements oper-

ates, the   symbol lights up. The symbol 

goes out, if none of the heating elements 

operates (e.g. when the oven reaches the 

desired temperature and the heating ele-

ments are disconnected until the tempera-

ture drops).

Heating functions

Touch   to select heating functions. You 

can use the following controls:

 – open pre-set programmes menu (clear 

unconfirmed settings);

  –  open  timer  menu  (clear  unconfirmed 

settings);

 – go back. If you are on the main screen 

– clear settings and enter operating mode.

,   – navigate the menu;

OK – confirm.

[do nothing for 20s] - if you do nothing for 20 

seconds, settings are cleared and the appli-

ance enters operating mode. 

The text display (left) shows the message 

"Select heating function >" and ">" is blink-

ing. Heating functions are displayed se-

quentially. The default function is Fan cook

-

ing. Note: Rotisserie functions only appear 

on appliances that feature rotisserie. Out of 

the three cleaning function available only 

the active function is displayed, depending 

on the pyrolysis settings.

In addition to accompanying functions, dif-

ferent oven chamber outline symbols are 

displayed  reflecting  the  selected  heating 

function. Touch   or   to select and then 

OK to confirm.

Once your selection is made, it is displayed 

on the left side while the right side is blank. 

The  default  oven  temperature  flashes. 

Touch   or 

  to  adjust  temperature  and 

then OK to confirm.

If meat probe is detected, the appliance will 

ask you to select its temperature. Touch   

or 

 to adjust default meat probe tempera

-

ture of 80°C and then OK to confirm. 

This step is omitted if no meat probe is de-

tected.

Oven light is on switches, and you can use 

 and   sensors. Other functions start af

Summary of Contents for 10203.3TzDpsScLbJVSm









































Reviews: