manualshive.com logo in svg

Ametek Teseq NSG 3150, User Manual, Page: 42 / 59

Share
Download
Ametek Teseq NSG 3150 User Manual Download Page 42

 

 

42 

8.5  EUT fail input 

Between pin 6 (hi) and pin 2, 8, 15, 20 (low) 
Input open = inactive; input shorted = active 

This connection serves as a control input that can be activated externally. 

The EUT can activate this input if it is capable of reporting a disturbance effect caused during an EMC 
test. Such events are time / date stamped by the system and are stored together with the current test 
parameters for subsequent use in a test report if required. 

8.6  EUT power off 

Between pin 4 (hi) and pin 2, 8, 15, 20 (low) 

Input open =  

Inactive, EUT power is controlled via front panel or WIN 3000 software 

Input shorted =  Active, in case EUT power is switched on, shorting this input will set EUT power to off  

 

Notes: 

1.  Using this function only makes sense if an EUT power contactor is available somewhere in the 

system. EUT power contactors are available in CDN 3153-S63. 

2.  First the  EUT  power  has  to  be  switched ON  via front  panel  or WIN  3000  software. This  way 

allows dual drive, as the EUT power can then be switched OFF either from software control or 
from this external drive. 

3.  This signal is also used to drive the orange lamp of INA 3001 warning lamps. 

8.7  High voltage active 

Between pin 16 (Hi) and pin 2, 8, 15, 20 (low). 

This function is activated for firmware revisions 2.30 and higher. 

This  output  is  to  drive  external  warning  lamps INA  3001. The  HV  on  signal  is  working  together  with 
the high voltage LED located on the front panel. 

Output high (24 V): High voltage is ON 
Output low (0 V): High voltage is OFF 

 

 

 

Summary of Contents for Teseq NSG 3150




























































Reviews:

No comments