background image

Page 15

For technical questions, please call 1-888-866-5797.

Item 64021

Sa

FE

ty

Op

E

ra

ti

O

n

Maint

E

nanc

E

S

E

tup

Maintenance and Servicing

  procedures not specifically explained in this manual 

must be performed only by a qualified technician.

cleaning, Maintenance, and Lubrication

1.  Wipe unit with a dry, lint-free cloth.  

Do not use solvents or abrasives.

2.  Remove battery if not in 

use for long periods.

3.  Store unit in a dry location.

4.  Other than the battery and fuses, 

there are no replaceable parts 
in this unit.  

repairs should be 

done by a qualified technician.

Battery/Fuse replacement

If the   sign appears on the Display, 
the battery should be replaced.

1.  Remove Test Leads from the Meter.

2.  Power off Meter and turn it over.

3.  Remove screw(s).  Remove tilt 

stand and battery cover.

4.  Replace 

Battery

.

a.  Remove battery from the 

battery compartment.

b.  Replace battery with the 

same type and rating.

note:

  Do not reverse the 

polarity of the battery.

5.  Replace 

Fuse(s)

.

a.  Remove screw(s) from case bottom 

and separate case top from bottom.

b.  Carefully remove fuses one at a 

time.  Gently pry one end loose 
and remove from its bracket.  

Make note of its rating

.

c.  Replace with new fuse of the 

same type and rating.

6.  Rejoin the tilt stand, battery 

cover and case bottom.  
Reinstall and tighten screw(s).

calibration

Have the Meter calibrated by a qualified technician every year.

Summary of Contents for 64021

















Reviews: