background image

Page 4

For technical questions, please call 1-888-866-5797.

Item 64021

Sa
FE
ty

Op
E

ra
ti

O

n

Maint

E

nanc

E

S

E

tup

15.  People with pacemakers should 

consult their physician(s) before use.  
Electromagnetic fields in close 
proximity to heart pacemaker could 
cause pacemaker interference 
or pacemaker failure.

16.  Do not test voltage on circuits 

higher than 1000 volts.

17.  Do not test current on circuits 

higher than 10 amps.

18.  Dress properly.  Protective, 

electrically nonconductive 
clothes and nonskid footwear are 
recommended when working.

19.  Wear ANSI-approved safety 

goggles during use.

20.  Only use accessories intended 

for use with this meter.

21.  Avoid damaging meter. Use only 

as specified in this manual.

22.  Prior to testing resistance, diodes, 

or continuity; disconnect all power 
to the circuit and discharge all 
high-voltage capacitors.

23.  Performance of this meter may vary 

depending on battery condition.

24.  Use the proper settings, terminals, 

techniques, and range for the 
tests performed.  Start with the 
range stated in the instructions.

25.  Do not apply voltage to the 

Test Leads when the Multimeter 
is in the Ohms testing setting.  
Damage can occur to the Meter.

26.  Do not switch between testing 

modes with the multimeter 
connected to a circuit.

27.  Do not use the meter at a setting 

marked as blank on the scale.

28.  Have the Multimeter calibrated by 

a qualified technician every year 
to maintain accurate results.

29.  Do not disassemble charger; 

take it to a qualified technician 
when service or repair is required. 
Incorrect reassembly may result 
in a risk of electric shock or fire.

30.  The warnings, cautions, and 

instructions discussed in this 
instruction manual cannot cover all 
possible conditions and situations 
that may occur. It must be understood 
by the operator that common sense 
and caution are factors which cannot 
be built into this product, but must 
be supplied by the operator.

 SaVE tHESE inStructiOnS.

Summary of Contents for 64021

















Reviews: