background image

Page 8

For technical questions, please call 1-888-866-5797.

Item 64021

Sa
FE
ty

Op
E

ra
ti

O

n

Maint

E

nanc

E

S

E

tup

Operating instructions

  read the EntirE iMpOrtant SaFEty inFOrMatiOn section 

at the beginning of this manual including all text under 
subheadings therein before set up or use of this product.

Electrical shock can cause death or injury! nEVEr tOucH 
exposed conductors of electricity

.

General Operation

ranGE Button

The 

ranGE

 Button enables manual selection of available ranges for the selected 

function.  The Meter’s default is 

autorange (autO) 

where the Meter selects for you

.

1.  To select manual ranging mode, hold 

down 

ranGE 

Button until the Meter 

beeps.  The Meter is in manual mode 
when 

Manu

 is seen on the Display.

2.  Each press of the 

ranGE

 Button 

steps through the ranges available 
for the selected function.

3.  To return to Autorange, hold down 

the 

ranGE

 Button for about 2 

seconds or until the Meter beeps.  
The Meter is in Autorange when 

autO

 is seen on the Display.

MaX Min Button

The 

MaX Min

 Button allows you to record, temporarily store and 

view signal events as you monitor them.  You may record while in 
any range or mode except Hz% (frequency/duty cycle).

1.  Press the 

MaX Min

 (maximum/

minimum) Button to begin 
recording.  Note that the Meter 
automatically resets to manual 
range mode when measuring 
minimum / maximum values.

2.  When you are finished recording, 

press the 

MaX Min

 Button to scroll 

through the high (maximum) and low 
(minimum) recorded readings.  The 
readings will be seen on the Display.

3.  To return to normal operating 

mode, hold down the 

MaX Min

 

Button for about 2 seconds.

rEL   Button

The 

rEL

 (relative mode) Button can be used in all modes except Hz% 

(frequency/duty cycle).  Relative mode subtracts a stored value from the present 
measurement and displays the result.  For example, if the stored value is 20.0V 
and the present measurement is 22.0V then the Meter will display 2.0V.

1.  To enter relative mode, press the 

rEL

   Button.  The present 

measurement will lock and 
the Meter will display “0”.

2.  Take a new measurement and the 

Meter will display the relative value.

3.  Press the 

rEL

   Button again to reset 

the stored value and exit relative mode.

Summary of Contents for 64021

















Reviews: