AmeriWater MediQA MDP Series Operation & Maintenance Manual Download Page 14

Page: 14 / 100

98-0157 Rev K

3.6

PERFORMANCE PARAMETERS

MediQA Performance Parameters

Single Pass

Dual Pass

Catalog Number

MSP2

MSP3

MDP2

MDP4

Flow Rates

Product Flow Specification (GPM)

Product Flow Range (GPM)

7.2-10.8

9.6-14.4

4.8-7.2

8-12

Stage 1 Concentrate Flow (GPM)

Nominal: 5

3.8-9

Nominal: 6.5

5-12

Nominal: 5

3.8-9

Nominal: 6.5

5-12

Stage 2 Concentrate Flow (GPM)

1-3

Stage 1 Recovery (%)

Nominal: 65

50-70

Nominal: 65

50-70

Nominal: 65

50-70

Nominal: 65

50-70

Stage 2 Recovery (%)

Nominal: 80

75-85

Nominal: 80

75-85

Pressure

Stage 1 Pump Pressure (PSI)

140-180

Stage 2 Pump Pressure (PSI)

140-180

Feed Water Pressure (PSI)

30-80

Interstage Pressure [Bar]

(PSI)

2-5

(30-70)

2-5

(30-70)

Temperature

Feed Water Temperatures (F)

40-90

Conductivity

Output Conductivity

>94% Incoming

Water



Based on Standard Recovery Mode



Each MediQA should perform within these parameters. Pressures may vary depending on the age and condition of the membrane.



*The ideal Feed water temperature is 77 degrees Fahrenheit. This will be the optimal operation temperature of the system.



The DOW heat disinfection membranes are manufactured with a ±20% tolerance for flow rate. This is factored into the Product Flow Range category.



Output conductivity is based on the quality of the feed water. The output conductivity should be greater than 94% of the incoming feed water.

Summary of Contents for MediQA MDP Series





































































































Search results

Summary of Contents for MediQA MDP Series

Reviews:

Brands by name

Popular brands

AmeriWater MediQA MDP Series, Operation & Maintenance Manual

Search results

Summary of Contents for MediQA MDP Series

Reviews:

Brands by name

Popular brands