AmeriGlide Hercules II Hybrid Installation Manual Download Page 6

Page: 6 / 34

HERCULES II HYBRID INSTALLATION GUIDE

(800) 580-0831

www.AmeriGlide.com

AmeriGlide

The

Hercules II Hybrid

Vertical Platform Lift has been designed to meet

CSA B613-00

& B355-15

standards. Code requirements and standards for vertical platform lifts vary

depending on location and region. It is the installer’s responsibility to contact their

local code enforcement office and determine all of the regulations they are subject to

before installing the

Hercules II Hybrid

Vertical Platform Lift.

The

Hercules II Hybrid

Vertical Platform Lift requires a 110VDC-15 AMP grounded

electrical circuit and a GFCI protected circuit. Depending on local codes and

regulations, this connection may need to be routed in electrical conduit and hard-

wired.

- Upon receipt of the

Hercules II Hybrid

Vertical Platform Lift, verify the lift for

shipping damage immediately. Report any discrepancies or damage claims to your

dealer.
- Carefully verify all the site specifics, technical drawings and all preparatory work

prior to installation.

The

Hercules II Hybrid

must be installed on a Supporting Wall and Floor that is

capable of supporting the minimum load and standards as laid out in the Technical

Drawings. Please read and verify with the Technical Drawings before beginning the

installation of the

Hercules II Hybrid

CODES AND STANDARDS

ELECTRICAL REQUIREMENTS

BEFORE YOU GET STARTED

SITE REQUIREMENTS

DO NOT OPERATE OR RIDE ON THE LIFT UNTIL IT HAS BEEN ANCHORED TO AN APPROVED PAD OR

FLOOR.

WARNING

Summary of Contents for Hercules II Hybrid



































Search results

Summary of Contents for Hercules II Hybrid

Reviews:

Related manuals for Hercules II Hybrid

Brands by name

Popular brands

AmeriGlide Hercules II Hybrid, Installation Manual

Search results

Summary of Contents for Hercules II Hybrid

Reviews:

Related manuals for Hercules II Hybrid

Brands by name

Popular brands