AmeriGlide Hercules II Hybrid Installation Manual Download Page 19 | Manualshive

Page: 19 / 34

background image

19

HERCULES II HYBRID INSTALLATION GUIDE

(800) 580-0831

www.AmeriGlide.com

AmeriGlide

INSTALL

1. Attach the Timing Belt and Timing Belt Clamp to the Drive Unit Shelf.

ENSURE THE

TIMING BELT’S COGGED RUBBER TEETH FACE TOWARDS THE CARRIAGE.

2. Thread the Timing Belt through the Speed Governor.

REFER TO THE TIMING BELT

DIAGRAM ON THE SPEED GOVERNOR.

3. Attach the bottom of the timing belt to the bracket on the Tension release

assembly.

15. INSTALL TIMING BELT AND TENSION RELEASE

ENSURE THAT THERE IS NOT TOO MUCH TENSION ON THE TIMING BELT. EXCESSIVE TENSION ON

THE TIMING BELT CAN DAMAGE THE TIMING BELT AND COMPROMISE OTHER COMPONENTS.

WARNING

Timing Belt

Tension Release Spring

Tension Release

Assembly Bracket

Timing Belt

Speed Governor Assembly

«
...
17
18
19
20
21
...
»

Summary of Contents for Hercules II Hybrid



































Reviews:

No comments

Related manuals for Hercules II Hybrid

Brand: Happ Pages: 49

Brand: KAR-TECH Pages: 28

UTILITY UTAC13-0

Brand: WIA Pages: 8

Pulse-Expert M-400S

Brand: Masterweld Pages: 25

Brand: Nedap Pages: 5

Brand: liquidarc Pages: 36

Brand: ICP DAS USA Pages: 6

ADAP-KOOL AK-SM 800

Brand: Danfoss Pages: 4

Brand: R. Beck Maschinenbau Pages: 40

HOBBY WELD K1790-1

Brand: Lincoln Electric Pages: 24

VIPER SYNERGIC MIG165

Brand: Xcel-Arc Pages: 58

Brand: WinSystems Pages: 30

DMU380SA Series

Brand: Memsic Pages: 105

Brand: GMI Pages: 10

Brand: Zepro Pages: 6

2200 Traditional Series

Brand: Zephir Pages: 2

Brand: Thermal Arc Pages: 62

Brand: Oase Pages: 87

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands