American-Lincoln 3366XP Instructions For Use Manual Download Page 22

Page: 22 / 24

American-Lincoln

Technology

3366XP / 4366XP

- FORM NO. 56041668

TECHNICAL SPECIFICATIONS (as installed and tested on the unit )

Model

4366XP LD LPG

4366XP VD LPG

4366XP LD Petrol

4366XP VD Petrol

4366XP LD Diesel

4366XP VD Diesel

Model No.

579-549

579-547

579-548

579-546

579-551

579-550

Sound Pressure Level (ISO 11201)

dB (A)

92.3

Sound Power Level (ISO 3744)

dB (A)

Lwa 112.1

Total Weight

lbs/kg

3580 / 1624

3800 / 1724

Vibrations at the Hand Controls (ISO 5349-1)

m/s

0.93 m/s

Vibrations at the Seat (EN 1032)

m/s

0.54 m/s

Gradeability

21% (11.8°)

Model

3366XP LD Petrol

3366XP VD Petrol

3366XP LD Diesel

3366XP VD Diesel

Model No.

579-548CE

579-546CE

579-551CE

579-550CE

Sound Pressure Level (ISO 11201)

dB (A)

92.3

Sound Power Level (ISO 3744)

dB (A)

Lwa 112.1

Total Weight

lbs/kg

3580 / 1624

3800 / 1724

Vibrations at the Hand Controls (ISO 5349-1)

m/s

0.93 m/s

Vibrations at the Seat (EN 1032)

m/s

0.54 m/s

Gradeability

21% (11.8°)

revised 1/07

Summary of Contents for 3366XP

























Search results

Summary of Contents for 3366XP

Reviews:

Related manuals for 3366XP

Brands by name

Popular brands

American-Lincoln 3366XP, Instructions For Use Manual

Search results

Summary of Contents for 3366XP

Reviews:

Related manuals for 3366XP

Brands by name

Popular brands