American Dryer Corp. ML-75DIII Installation Manual Download Page 26

Page: 26 / 65

3. Grounding

A ground (earth) connection

must be

provided and installed in accordance with state and local codes. In

the absence of these codes, grounding

must conform

to applicable requirements of the National Electrical

Code ANSI/NFPA NO. 70-LATEST EDITION, or in Canada, the installation

must conform

to applicable

Canada Standards: Canadian Electrical Codes Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION. The

ground connection may be to a proven earth ground at the location service panel.

For added personal safety, when possible, it is suggested that a separate ground wire (no. 18 minimum) be

connected from the ground connection of the dryer to a grounded cold water pipe.

DO NOT

ground to a

gas pipe or hot water pipe.

The grounded cold water pipe

must have

metal to metal connection

ALL

the

way to the electrical ground. If there are any nonmetallic interruptions, such as, a meter, pump, plastic,

rubber, or other insulating connectors, they

must be

jumped out with no. 4 copper wire and securely

clamped to bare metal at both ends.

IMPORTANT:

For personal safety and proper operation, the dryer

must be

grounded.

Provisions are made for ground connection in each dryer at the electrical service connection area.

4. Electrical Connections

NOTE:

A wire diagram is located in the front electrical control box for connection data.

a. Gas and Steam Models Only

NOTE: A CIRCUIT SERVICING EACH DRYER

MUST BE

PROVIDED.

1) Single-Phase (1ø) Wiring Connections (Hookup)

The electrical connections on

ALL

single-phase

(1ø) gas and steam dryers are made into the rear

service box located at the upper left area of the

dryer.

Actual electrical wire connections are made to

the L1 and L2 terminals of the motor contactor

located in the rear service box mentioned above.

The ground connection is also made to the copper

lug also provided in this box.

Summary of Contents for ML-75DIII


































































Search results

Summary of Contents for ML-75DIII

Reviews:

Related manuals for ML-75DIII

Brands by name

Popular brands

American Dryer Corp. ML-75DIII, Installation Manual

Search results

Summary of Contents for ML-75DIII

Reviews:

Related manuals for ML-75DIII

Brands by name

Popular brands