American Dryer Corp. ML-75DIII Installation Manual Download Page 19

Page: 19 / 65

IMPORTANT:

Minimum ductwork diameter for horizontal venting is 10-inches (25.4 cm) and for

vertical venting the minimum is 12-inches (30.48 cm).

NOTE:

When the exhaust ductwork passes through a wall, ceiling, or roof made of combustible

materials, the opening

must be

2-inches (5.08 cm) larger than the duct (all the way around).

The duct

must be

centered within this opening.

a. Outside Ductwork Protection

1) To protect the outside end of horizontal ductwork from the weather, a 90° elbow bent downward

should be

installed where the exhaust exits the building. If the ductwork travels vertically up

through the roof, it

should be

protected from the weather by using a 180° turn to point the opening

downward. In either case, allow at least twice the diameter of the duct between the duct opening

and the nearest obstruction.

IMPORTANT:

DO NOT

use screens, louvers, or caps on the outside opening of the exhaust

ductwork.

2. Single Dryer Venting

Where possible, it is suggested to provide a separate exhaust duct for each dryer. The exhaust duct

should

laid out in such a way that the ductwork travels as directly as possible to the outdoors with as few turns

as possible. It is suggested that the use of 90° turns in the ducting be avoided; use 30° and/or 45° angles

instead. The shape of the exhaust ductwork is not critical so long as the minimum cross section area is

provided.

IMPORTANT:

Minimum duct size for a dryer that is vented horizontally is 10-inches (25.4 cm) for a

round duct or an equivalent of 80 square inches (516 square centimeters).

THE

DUCT SIZE

MUST NOT

REDUCED ANYWHERE DOWNSTREAM OF

THE DRYER.

IMPORTANT:

Exhaust back pressure measured by a manometer at each basket (tumbler) exhaust

duct area

must be

no less than 0 and

must not exceed

0.3 inches (0.74 mb) of water

column (W.C.).

IMPORTANT:

Minimum duct size for a dryer that is vented vertically is 12-inches (30.48 cm) for a

round duct or an equivalent of 120 square inches (774 square centimeters).

THE

DUCT SIZE

MUST NOT

REDUCED ANYWHERE DOWNSTREAM OF

THE DRYER.

Summary of Contents for ML-75DIII


































































Search results

Summary of Contents for ML-75DIII

Reviews:

Related manuals for ML-75DIII

Brands by name

Popular brands

American Dryer Corp. ML-75DIII, Installation Manual

Search results

Summary of Contents for ML-75DIII

Reviews:

Related manuals for ML-75DIII

Brands by name

Popular brands