American Dryer Corp. ML-75DIII Installation Manual Download Page 24

Page: 24 / 65

2. Electrical Service Specifications

a. Gas and Steam Models Only

IMPORTANT:

Figures shown are for non-reversing models only. For reversing models contact the

factory.

IMPORTANT:

The dryer

must be

connected to the electric supply shown on the data label that is

affixed to the left side panel/wall area behind the control door. In the case of 208

VAC or 240 VAC, the supply voltage

must match

the electric service specifications

of the data label

exactly

IMPORTANT:

The wire size

must be

properly sized to handle the related current.

WARNING: 208 VAC AND 240 VAC ARE

NOT

THE

SAME.

Any damage done to dryer

components due to improper voltage connections will automatically VOID THE

WARRANTY.

NOTE: ADC

reserves the right to make changes in specifications at any time without notice or

obligation.

M LG-75 (G

)

M LS-75 (S

TEAM

)

ELECTRICAL SERVICE SPECIFICATIONS (PER DRYER)

IMPORTANT: 208 VAC and 240 VAC ARE NOT THE SAME. When ordering, specify exact voltage.

NOTES:

A. Fuse ratings are dual element, time delay, current limiting, class RK1 or RK5 ONLY.
B. Circuit breakers are thermal/magnetic (industrial) motor curve type ONLY. For others, calculate/verify correct

breaker size according to appliance amp draw rating and type of breaker used.

C. Circuit breakers for 3-phase (3ø) dryers must be 3-pole type.

SERVICE

VOLTAGE

PHASE

WIRE

SERVICE

APPROX.

AMP DRAW

MINIMUM

WIRE SIZE

FUSING

CIRCUIT

BREAKER

Dual Element

Time Delay

120 (60 Hz)

208 (60 Hz)

7.6

208 (60 Hz)

3/4

4.7

240 (50/60 Hz)

1ø

240 (50/60 Hz)

3ø

3/4

4.9

380-400 (50 Hz)

3/4

416 (50 Hz)

3/4

3.1

460 (60 Hz)

3/4

2.8

* AWG Stranded Wire Type ... size wire as per National Electrical Code or local codes.

Summary of Contents for ML-75DIII


































































Search results

Summary of Contents for ML-75DIII

Reviews:

Related manuals for ML-75DIII

Brands by name

Popular brands

American Dryer Corp. ML-75DIII, Installation Manual

Search results

Summary of Contents for ML-75DIII

Reviews:

Related manuals for ML-75DIII

Brands by name

Popular brands