background image

4

B.  SAFETY PRECAUTIONS

WARNING:

For your safety, the information in this manual 

must be

 followed to minimize the risk of

fire or explosion or to prevent property damage, personal injury, or loss of life.

WARNING: The dryer 

must never be 

operated with any of the back guards, outer tops, or

service panels removed.  PERSONAL INJURY or FIRE COULD RESULT.

1.

DO NOT

 store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

2. Purchaser/user should consult the local gas supplier for proper instructions to be followed in the event the

user smells gas.  The instructions 

should be

 posted in a prominent location.

3. WHAT TO DO IF YOU SMELL GAS...

a.

DO NOT

 try to light any appliance.

b.

DO NOT

 touch any electrical switch.

c.

DO NOT

 use any phone in your building.

d. Clear the room, building, or area of 

ALL

 occupants.

e. Immediately call your gas supplier from a neighbor’s phone.  Follow the gas supplier’s instructions.

f. If you 

cannot

 reach your gas supplier, call the fire department.

4. Installation and service 

must be

 performed by a qualified installer, service agency, or gas supplier.

5. Dryer(s) 

must be

 exhausted to the outdoors.

6. Although 

ADC

 produces a very versatile dryer, there are some articles that, due to fabric composition or

cleaning method, 

should not be 

dried in it.

WARNING:

Dry only water washed fabrics.  

DO NOT

 dry articles spotted or washed in dry

cleaning solvents, a combustible detergent, or “all purpose” cleaner.

EXPLOSION COULD RESULT.

WARNING:

DO NOT

 dry rags or articles coated or contaminated with gasoline, kerosene, oil, paint,

or wax.

EXPLOSION COULD RESULT.

WARNING:

DO NOT

 dry mop heads.  Contamination by wax or flammable solvents will create a

fire hazard.

WARNING:

DO NOT

 use heat for drying articles that contain plastic, foam, sponge rubber, or

similarly textured rubber materials.  Drying in a heated basket (tumbler) may damage

plastics or rubber and also may be a fire hazard.

Summary of Contents for ML-75DIII


































































Reviews: