American Dryer Corp. ML-75DIII Installation Manual Download Page 41

Page: 41 / 65

5. Electrically Heated Dryers

a. Check to insure that electric oven/contactor assembly is activating.

6. Make a complete operational check of

ALL

safety related circuits:

a. Door Switch(es)

b. Hi-Limit Thermostats

c. Sail Switch (for Gas and Electric Models Only)

NOTE:

To check for proper sail switch operation (for gas and electric models only), open the main

door and while holding main door switch plunger in, start dryer. Dryer should start but heat

circuit

should not be

activated (on). If the heat system is activated, the sail switch is

improperly adjusted and

must be

adjusted by bending the actuator arm of the sail switch

toward the burner box. If the actuator arm is bent too far toward the burner box of the dryer,

the dryer

may not

have heat when needed. After any adjustment to the sail switch, the above

procedure

must be

repeated to verify proper operation of the sail switch.

7. The dryer

should be

operated through one (1) complete cycle to assure that no further adjustments are

necessary and that

ALL

components are functioning properly.

BASKET COATING

The basket (tumbler) is treated with a protective coating. We suggest dampening old garments or cloth material

with a solution of water and nonflammable mild detergent and tumbling them in the basket (tumbler) to remove

this coating.

8. Make a complete operational check of

ALL

operating controls.

a. For microprocessor model check controller (computer) programs/selections...

1) Each microprocessor controller (computer) has been preprogrammed by the factory with the most

commonly used parameter (program) selections. If computer program changes are required, refer

to the computer programming manual which was shipped with the dryer.

9. Check the electric service phase sequence (3-phase [3ø] models only). While the dryer is operating, check

to see if the blower wheel (impellor/fan) is rotating in the proper direction. Looking from the front, the

blower wheel (impellor/fan) should spin in the clockwise (CW) direction. If it is, the phasing is correct. If

the phasing is incorrect, reverse two (2) of the three (3) leads at connections L1, L2, L3 of the power

supply to the dryer.

IMPORTANT:

If the blower wheel (impellor/fan) is rotating in the wrong direction, this

will not

only

drastically reduce drying efficiency, but it can also cause premature component failure.

Summary of Contents for ML-75DIII


































































Search results

Summary of Contents for ML-75DIII

Reviews:

Related manuals for ML-75DIII

Brands by name

Popular brands

American Dryer Corp. ML-75DIII, Installation Manual

Search results

Summary of Contents for ML-75DIII

Reviews:

Related manuals for ML-75DIII

Brands by name

Popular brands