![background image](http://html1.mh-extra.com/html/american-dj/vizi-led-spot/vizi-led-spot_user-instructions_2923237007.webp)
American DJ
®
- www.americandj.com - Vizi LED Spot - Instruction Manual - Page 14
American DJ
®
- www.americandj.com - Vizi LED Spot - Instruction Manual - Page 13
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
fixtures may be implemented in a 3-pin DMX line. When inserting stan-
dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
Conductor
5-Pin XLR Male (In)
3-Pin XLR Female (Out)
Pin 1
Pin 5 - Do Not Use
Pin 4 - Do Not Use
Pin 3
Pin 2
Pin 1
Pin 3
Pin 2
Not Used
Not Used
Data True (+ signal)
Data Compliment (- signal)
Ground/Shield
3-Pin XLR to 5-Pin XLR Conversion
Vizi LED Spot
Set Up
Vizi LED Spot
System Menu
0
ADDR
AXXX A001
Indicate the staring DMX address
A001 also is the setting for slave
1
TEST
T-01~T-XX
Automatically test the function
RUN
MSTR/ALON
Runs fixture as “master” or “alone” for auto
AUDI
MSTR/ALON
Runs fixture as “master” or “alone” for
audio
2
PLAY
AUTO
Clos/Hold/Auto/Audi
No DMX Status
ALL
Reset all motors and returns fixture to home
SCAN
Reset only motors for pan/tilt
COLR
Reset only motors for colors
GOBO
Reset only motors for gobo and rotation
3
RESE
OTHR
Reset other motors
LIFE
0000~9999
Displays the total fixture running time
4
TIME
CLMP
Clear lamp running time
5
RPAN
ON/OFF
Reverses the pan movements
6
RTLT
ON/OFF
Reverses the tilt movements
7
FINE
ON/OFF
Switch 16 bit/8 bit
8
DEGR
540/630
Pan degree select
9
MIC
M-XX M-70
Mic sensitivity
VALU
D–XX D-00 (DXXX)
Display the DMX512 value of each channel
D ON
ON/OFF
Display turn off after 2mins
FLIP
ON/OFF
This function will reverse the display 180
10
DISP
LOCK
ON/OFF
Key lock
RDMX
ON/OFF
Change DMX address via external controller
SPOT
ON/OFF
Lamp optimization
DFSE
ON/OFF
Resets all the fixture functions to default
FEED
ON/OFF
Pan/tilt feedback (error correction) on/off
FANS
AUTO/HIGH/LOW
Fan’s mode select
VER
V1.0~V9.9
Software version
CODE
CXXX
Fixture code *code is “C050”
11
SPEC
ADJU
CH01~CHXX
XXXX(-128~127)
Motor Fix
SEPR
AUTO
IP01~IP07
Select program to be edit
STEP
S–01 ~S–48
Set the amount of your program
C–01~C–XX
0 1 XX(00~FFH)
XX XX(00~FFH)
Edit the channels of each scene
TIME
T XXX(001~999)
Time for each scene
SCXX
CEDT
ON/OFF
Edit program via controller
REC.
RE.XX
Auto Save
12
EDIT
RUN
ON/OFF
Program test