American DJ Vizi LED Spot User Instructions Download

Page: 2 / 26

Unpacking:

Thank you for purchasing the Vizi LED Spot by Ameri-

can DJ

. Every Vizi LED Spot has been thoroughly tested and has

been shipped in perfect operating condition. Carefully check the ship-
ping carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your fixture for any
damage and be sure all equipment necessary to operate the unit has
arrived intact. In the event damage has been found or parts are miss-
ing, please contact our toll free customer support number for further
instructions. Please do not return this unit to your dealer without con-
tacting customer support first.

Introduction:

The Vizi LED Spot is a compact, bright, moving head,

DMX intelligent fixture. The Vizi LED Spot can be either a 10 or 12
Channel DMX unit. The fixture can operate in three different operat-
ing modes; show mode, sound-active, or under DMX Control. The Vizi
LED Spot can be used as a stand alone unit or in a master/slave con-
figuration.

For best results use fog or special effects smoke to enhance

the beams projections.

Customer Support:

American DJ

provides a toll free customer

support line, to provide help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.americandj.com for any comments or
suggestions. Service Hours are Monday through Friday 9:00 a.m. to
4:30 p.m. Pacific Standard Time.

Voice:

(800) 322-6337

Fax:

(323) 582-2941

E-mail:

[email protected]

To purchase parts online visit http://parts.americandj.com

Warning!

To prevent or reduce the risk of electrical shock or fire, do

not expose this unit to rain or moisture.

Warning!

This may cause severe eye damage. Avoid looking directly

into the light source at all times!

Vizi LED Spot

Introduction

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

•   To reduce the risk of electrical shock or fire, do not expose this unit
   rain or moisture
•   Do not spill water or other liquids into or on to your unit.
•   Be sure that the local power outlet match that of the required volt-
   age for your unit.
•   Do not attempt to operate this unit if the power cord has been
   frayed or broken.
•   Do not attempt to remove or break off the ground prong from
   the electrical cord. This prong is used to reduce the risk of electrical
   shock and fire in case of an internal short.
•   Disconnect from main power before making any type of connection.
•   Do not remove the cover under any conditions. There are no user
   serviceable parts inside.
•   Never operate this unit when it’s cover is removed.
•   Always be sure to mount this unit in an area that will allow proper
   ventilation. Allow about 6” (15cm) between this device and a wall.
•   Do not attempt to operate this unit, if it becomes damaged.
•   This unit is intended for indoor use only, use of this product out-
   doors voids all warranties.
•   Always mount this unit in safe and stable matter.
•   Power-supply cords should be routed so that they are not likely to
   be walked on or pinched by items placed upon or against them,
   paying particular attention to cords at plugs, convenience recep-
   tacles, and the point where they exit from the appliance.
• Cleaning -The fixture should be cleaned only as recommended by
   the manufacturer. See page 48 for cleaning details.
•   Heat -This fixture should be situated away from heat sources such
   as radiators, heat registers, stoves, or other appliances (including
   amplifiers) that produce heat.
•   The fixture should be serviced by qualified service personnel when:
    A. Objects have fallen, or liquid has been spilled into the appliance.
    B. The appliance has been exposed to rain or water.
    C.  The  appliance  does  not  appear  to  operate  normally  or  exhibits  a