![background image](http://html1.mh-extra.com/html/american-dj/inno-color-beam-led/inno-color-beam-led_user-instructions_2923108011.webp)
ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 21
ADJ Products, LLC - www.adj.com - Inno Beam LED Instruction Manual Page 22
Inno Beam LED
12 Channel Mode
Channel Value
Function
1 0 - 255 PAN
2 0 - 255 TILT
3 COLORS
0 - 7 OPEN
8 - 14 RED
15 - 21 ORANGE
22 - 28 YELLOW
29 - 35 GREEN
36 - 42 BLUE
43 - 49 MAGENTA
50 - 56 LIGHT BLUE
57 - 63 PINK
64 - 127 SPLIT COLORS
128 - 189 RAINBOW EFFECT FAST - SLOW
190 - 193 STOP
194 - 255 RAINBOW EFFECT SLOW - FAST
4 GOBO WHEEL
0 - 7 OPEN
8 - 15 GOBO 1
16 - 23 GOBO 2
24 - 31 GOBO 3
32 - 39 GOBO 4
40 - 47 GOBO 5
48 - 55 GOBO 6
56 - 63 GOBO 7
64 - 71 OPEN SHAKE
72 - 79 GOBO 1 SHAKE
80 - 87 GOBO 2 SHAKE
88 - 95 GOBO 3 SHAKE
96 - 103 GOBO 4 SHAKE
104 - 111 GOBO 5 SHAKE
112 - 119 GOBO 6 SHAKE
120 - 127 GOBO 7 SHAKE
128 - 189 GOBO WHEEL ROTATION FAST - SLOW
190 - 193 STOP
194 - 255 GOBO WHEEL ROTATION SLOW - FAST
Inno Beam LED
Operation
Show Mode:
This mode allows either a single unit or several units
linked together, to run one of four shows that you choose.
1. Press the MENU button until
“
Show Mode
” is displayed, and
press ENTER.
2.
Press the UP or DOWN buttons until you find your desired show,
and press ENTER.
Inno Beam LED UC3 Control
The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout.
Stand By
Blackout the unit
Function
1. Sync. Strobe
2. Async strobe
3. Sound Strobe
Show
1-4
1. Press to select color
2. Hold to select gobo
Mode
Sound (LED OFF)
Show (LED
Slow Blinking)
LED ON
Master-Slave Configuration
This function will allow you to link up
to 16 units together and operate without a controller. The units will
be sound activated. In Master-Slave operation one unit will act as the
controlling unit and the others will react to the controlling units pro-
grams. Any unit can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The first unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.
2. On the Master unit find your desired show and set that show by
pressing the ENTER button.
3. On the slave units tap the MENU button until “
Slave Mode
” is
displayed, and Press ENTER. Choose either “
Slave 1
” or “
Slave
2
” and press ENTER. See pages 13-14 for more info.
4. The slave units will now follow the Master unit.
Inno Beam LED
Master-Slave Setup