background image

en

Content Page

1. Important Information ...........................................................................................................4

1.1. Qualification Requirements for Personnel Performing Spare Part Replacement .............4
1.2. Warnings and Cautions  ............................................................................................................................4
1.3. Data Security .................................................................................................................................................5
1.4. System Description .....................................................................................................................................6
1.5. Spare Parts......................................................................................................................................................7
1.6. Spare Part Replacement Process ...........................................................................................................8

 

2. How To Clean and Disinfect the Displaying Unit ................................................................9

 3. Preparing for Spare Part Replacement ..............................................................................10

3.1. Tools Needed  ............................................................................................................................................. 10

 4. How to Replace Spare Parts ................................................................................................11

4.1. Visualization Device Interface Board Replacement .....................................................................11

 5. Final Inspection and Test .....................................................................................................15

3

Summary of Contents for aBox 2

















Reviews: