Ambit U10C034 User Manual Download Page 66 | Manualshive

Page: 66 / 90

background image

U10C034 Telephony Version v1.4 June 2008

66

4.1 Battery

Battery relative information can be showed and settings can be changed. It has the following

commands.

set

Set the timer to disable Ethernet or USB interface when loosing A/C.

show

Show all battery relative settings.

4.2 CM

Provides the commands to show Cable Modem relative information and control downstream

channel, upstream channel, log display ON or off and firewall.

gotoDownstream

Changes to specific downstream channel.

gotoUpstream

Changes to specific upstream channel

log

Enable or disable message logging.

ping

Pings to the specific IP address from CM IP stack.

set

Enable or disable CM mini firewall.

show

Show various information including:
        ARP table
        BPI status
    CM certificates
    DOCSIS classifiers
    CM config file name and contents
    CPE info/table
    Downstream status and signal quality
    DSx message history
        CM event log

«
...
64
65
66
67
68
...
»

Summary of Contents for U10C034



























































































Reviews:

No comments

Related manuals for U10C034

TALON UDC SERIES

Brand: Kantronics Pages: 101

Brand: C-Data Pages: 24

Brand: TP-Link Pages: 98

Brand: US Robotics Pages: 245

Brand: Telecom Pages: 16

Brand: Zoom Pages: 36

Brand: NETGEAR Pages: 17

Brand: Conrad Pages: 4

Brand: Conrad Pages: 4

Brand: Zte Pages: 24

Brand: Zte Pages: 27

Brand: Radicom Pages: 43

Brand: Rae Pages: 42

Brand: CalAmp Pages: 71

Brand: Maxis Pages: 63

Brand: Paradyne Pages: 165

Brand: Campbell Pages: 56

Brand: 4G Systems Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands