Amana PGB**C Installation Instructions Manual Download Page 18

18

XIII. Accessories and Functional
Parts

Sheet Metal Accessories

Additional Amana accessories, as described in Table 4,
can be purchased to fit specific application needs. Ac-
cessories can be ordered by the part numbers in the
table and each accessory includes its own separate
instructions.

Accessory

Duct Transition Over/Under

Horizontal Duct Covers

Coil Guard Kit 

Compressor Sound Blanket

Horizontal Filter Kit

Propane Gas Conversion Kit

High Altitude Kit

Table 4

Accessory List

Functional Parts

Blower Housing

Flame Roll-Out Switch

Blower Motor

Gas Orifice

Blower Wheel

Heat Exchanger

Burner

High Limit Switch

Compressor

Secondary Limit

Condenser Coil

Ignitor/Flame Sensor

Condenser Fan Blade Induced Draft Motor
Condenser Fan Motor Pressure Switch
Contactor

Pressure Switch Hose

Evaporator Coil

Transformer

Fan Timer Board

Figure 16

Functional Parts List

General Information

1. Refer to the description in Figure 16 when ordering
any of the listed functional parts. Be sure to provide the
unit model, manufacturing, and serial numbers with the
order.

2. Although only functional parts are shown in Figure
16, all sheet metal parts, doors, etc. may be ordered by
description.

3. Parts are available from your Amana distributor.

Summary of Contents for PGB**C



















Reviews: