background image

23

Heat Anticipator Setting

The heat anticipator in the room thermostat must be

correctly adjusted to obtain the proper number of heat-

ing cycles per hour and to prevent the room tempera-

ture from “overshooting” the room thermostat setting.

Heat anticipator must be set at 0.7 amps.

2

1

OF
F

Low Voltage

Connections

Fan Off

Adjustments

Figure 23

Ignition Control

(Viewed in an Upflow Installation)

Air Circulation Fan Timing

All items in this section refer to the air circulation fan, not

to the induced draft fan. The timing sequence for the

induced draft fan is not adjustable.
When a call for cooling occurs, the circulation fan will

come on following a five second delay. It will remain on

for 45 seconds after the call for cooling ends. This fan

timing is not adjustable.
During normal heating operation, the circulation fan will

come on 36 seconds after the gas valve opens. This

timing is not adjustable.
As shipped, the circulation fan will remain on for 90

seconds after the gas valve closes. If desired, this

timing may be adjusted.  (Figures 23 and 24)

12

12

12

12

ON

OF

F

ON

OF

F

ON

OF

F

ON

OF

F

60 

Second

Delay

90 

Second

Delay

180

Second

Delay

120

Second

Delay

Switches viewed in an upflow installation.

Figure 24

X. Circulating Air  and Filters

Ductwork - Air Flow

Duct systems and register sizes must be properly de-

signed for the C.F.M. and external static pressure rating

of the furnace. Ductwork should be designed in accor-

dance with the recommended methods of “Air Condi-

tioning Contractors of America” Manual D.
A duct system must be installed in accordance with

Standards of the National Board of Fire Underwriters for

the Installation of Air Conditioning, Warm Air Heating

and Ventilating Systems. Pamphlets No. 90A and 90B.
The filter is designed for high velocity heating and

cooling applications. Filters must be inspected, cleaned

or changed every two months or as required. It is the

owner's responsibility to keep air filters clean. 

NOTE:

Dirty filters are the most common cause of inadequate

heating or cooling performance.
Guide dimples locate the bottom or side cutouts. Use a

straight edge to scribe lines connecting the dimples.

Cut out the opening on these lines. For bottom return air

connection, the bottom of the cabinet has to be re-

moved before the furnace is positioned on the raised

platform or set on top of the return air duct.
A closed return duct system must be used, with the

return duct sealed to the furnace casing. Supply and

return duct connections to the unit may be made with

flexible joints to minimize noise transmission. If a cen-

tral return is used, a connecting duct must be installed

between the unit and the utility room wall so the furnace

blower will not interfere with combustion air or draft.

The room, closet, or alcove must not be used as a

return air collecting chamber.
When the furnace is used in connection with a cooling

unit, the furnace should be installed in parallel with or

on the upstream side of the cooling unit to avoid con-

densation in the heating element. With a parallel flow

arrangement, the dampers or other means used to

control the flow of air must be adequate to prevent

chilled air from entering the furnace and, if manually

operated, must be equipped with means to prevent

operation of either unit unless the damper is in the full

heat or cool position.
When the furnace is installed without a cooling coil, it is

recommended that a removable access panel be pro-

vided in the outlet air duct. This opening shall be acces-

sible when the furnace is installed and shall be of such a

size that the heat exchanger can be viewed for visual

light inspection or such that a sampling probe can be

inserted into the air stream. The access panel must be

made to prevent air leaks when the furnace is in opera-

tion.
When the furnace is heating, the temperature of the

return air entering the furnace must be between 55°F

and 100°F.

Summary of Contents for GUC-X

































Reviews: