ADJUSTMENT
24
SBS
the step-by-step control mode.
Sequence of commands
OPEN-STOP-CLOSE-STOP-OPEN ...
OP
the
OPEN
control mode. The command to open the doors
CL
the
CLOSED
control mode. The command to close the doors
STOP
STOP
control mode. The command to stop the doors
PE
the pedestrian position control mode. The command for partial opening of door, if the partial
position of door is set (setting
P1-F2)
LL
the light lamp mode. lfthe door does not move, the commands to turn on and off the built-in
lighting of the drive (illumination) and lamp connection output
SL/LL
are executed. The
SL/LL
output is controlled with the remote if the light lamp
LL
output has been set up
(P8-F4
setting)
Recording the remote controls
ATTENTION!
lf you need to overwrite a previously recorded remote control (when you need
to record another button of the remote or record the remote in another mode), it must first be
deleted from memory!
The pressed button when recording will control the remote in the first mode in the list
(tab.
10).
All other buttons of the remote control will be recorded automatically in the order specified in
the
tab/e 70
modes (refers to the settings in which several buttons are recorded).
Table 70
SETTING
MODE
SBS
SBS
SBS
SBS
OP
OP
2
PE
LL
PE
STOP
STOP
3
LL
CL
CL
4
PE
LL
In the case of F1-F4 settings, the unused buttons of the remote control can be recorded for
control in other ALUTECH products, where
AT-4N
remote control can be recorded.
Table 11
,
Press and hold the button
I
PR./
(
1
for about 5 secs to enter the
mJ
programming mode
2
After the appearance
of'P1'
inscription press the button
IOP./ AJ
[B
3
After the appearance
of'P2'
inscription press the button
IST./
►
I
g
Using the button
IOP./ AJ
or
ICL/vJ
select the required setting of remote
1
□
�
�
4
lru}l
control recording in the menu'F1 ...
F6'
� [n]v:
5
After the appearance of required setting press the button
IST./
►
I
�
LEVIGATO DRIVES (LG SERIES) LEVIGATO ANTRIEBE (SERIE LG) COMMANDES LEVIGATO (SERIE LG)
ADJUSTMENT
6
'rc'
is shown on the display, which means that the recording of remote controls
[9
is expected
Press the selected control button 3 times on the remote
�
7
(the first control button)
The number which is to be assigned to the remote in the drive m
r
mory,
r
ll
[g
8
automatically appear on the display (with the button IOP./Alor 0../v the
number can be changed)
9
Press the button
IST./
►lto confirm; after that a dot will appear on the display
g
In three seconds the automatic switch to the recording of the next remote con-
�
10
trol will take place. To exit the programming mode press the button
I
PR./<
I
three times or wait for 15 seconds (until automatic exit the setup menu)
Deleting the remote control and defining of the record number of the remote
The
tab/e
7
2
describes the settings, it is used when there is a remote control but the information
for the remote control number in the drive memory is not available.
Tobte 12
1
Press and hold the button IPR./(lfor about 5 secs to enter the
[il
programming mode
2
After the appearance of'P1' inscription press the button IOP./ Al
[B
3
After the appearance of'P2' inscription press the button
IST./
►
I
�
With the button IOP./AlorlO../vlselect the required setting:
1
□
�
4
'F7'-defining the number of the remote control;
'Sr./
,
� �
'FS'-deleting the remote control
�
5
After the appearance of required setting ('F7' or'FS') press the button
IST./
►
I
ml
6
'rc'
is shown on the display, which means that a signal from the remote control
[9
is expected
7
Press the selected control button 3 times
�
The display will automatically show the number of the remote control in the
[D
8
drive memory. lf the remote control is not recorded,'no' will be shown on the
display
Toset 'FS' press the button
IST./
►
�
A dot will disappear from the display, this
g
9
means that the remote control with the selected number is deleted from the
memory
LEVIGATO DRIVES (LG SERIES) LEVIGATO ANTRIEBE (SERIE LG) COMMANDES LEVIGATO (SERIE LG)
25
