manualshive.com logo in svg

Alton ABCEDOCT1010, Instruction Manual

Share
Download
Alton ABCEDOCT1010 Instruction Manual Download Page 33

33 

 

Dia. 56 

Slatted Roof Installation (optional)

 

11 

Diagram 56 

AB0048 

You will need to trim the felt at the corners, trim the 
bottom layer and overlap the top layer.  Then push the 
fascia up until it touches the underside of the bottom 
slat.  The treated softwood frame should then sit in 
behind it (diagram 56).   Fix the fascia in place with 
40mm pan head stainless steel screws,  this will then 
support the roof section while you fix the rest of the 
fascias.  

With all the felt in place you can lower the first slatted roof panel into place.  Its best to start above 
the door and work around the building from there.  Ask a helper to hold the first roof panel while you 
position the fascia board below.   You will notice the holes are slightly off-set, these should be closest 
to the bottom edge of the fascia in this installation. 
Make sure the felt is folded down tight along the bottom of the roof, also line up the ends of the 
fascia with the corner of the soffits.  The more time you take over lining these up will make a big 
difference to the overall finish. 

Diagram 55 

Summary of Contents for ABCEDOCT1010















































Reviews:

No comments

Brands by name

Popular brands

Load more brands