Alto Vision 17B, Operator'S Manual

Page: 47 / 55

Ref Part No. Description Qty
1 * Housing Brush End 1
2 * Field Assembly 1
3 50147A Armature Assembly 1
4 * Housing, Plain End 1
5 * Roll Pin 1
6 51861A Lead/BR Card Assembly 1
7 902679 Ball Bearing 1
8 51181A Ball Bearing 2
9 * Printed Mylar Stock 1
10 * Loctite 404 1
11 55412A #404 Woodruff Key 1
12 56671A O Ring 1
13 * Sealant
14 * Stud, 10-32 X 6.45 2
15 53319A Load Spring 1
16 * Nut, Keps 10-32 6
17 * Loctite 404
18 * Gear Housing 1
CLARKE TECHNOLOGY
Vision 17BT
Traverse Motor Drawing & Parts List 2/96
Motor #45031A
Ref Part No. Description Qty
19 * Gear Cap 1
20 51180A Ball Bearing 1
21 51179A Ball Bearing 1
22 58318A Output Shift 1
23 54414A Worm Gear 1
24 * Retaining Ring 1
25 * Key 1 /
8
x 1 /
8
1
26 59869A Worm 1
27 925597 Roll Pin 1
28 Retaining Ring 1
29 962892 Screw, ¼ - 20 1
30 980614 Lock Washer ¼" 1
31 * Screw, 10-32 SEMS 4
32 58694A Load Spring 1
33 59868A Washer 1
34 57850A Ring, Bearing Mounting 1
35 * Grease, Nyooel 15#
36 * Spacer 1
*Illustrated for assembly reference only.
Page -46- CLARKE TECHNOLOGY Operator's Manual -Vision 17B/BT
Shaft Sub Assembly Instructions
1. Assemble the retaining ring (24) to the output shaft (22) centering
the middle tab of the "E" ring in the keyway. The center tab
should bottom in the keyway.
2. Assemble the key (25) to the output shaft (22) butting the key
against the center tab of the retaining ring (24). Dimensions over
the key and shaft is .381.
3. Assemble gear (23). The gear should be started by hand over the
shaft and key to assure proper alignment and butt against the
retaining ring (24).
4. Assemble spacer (36).
5. Assemble the bearing (8) onto the shaft with the seal to the
inside. Press only on the inner race until the bearings are butted
securely against the gear spacer on one side and against the "E"
ring on the other side.
Fill gear housing and
apply to gear teeth.
See shaft sub-assembly
above for asm. details
36
35
32
33
11
19
31
Torque 15-25 lb.-in.
(4) pieces
34
28
20
18
27
26
15
29
30
31
Torque 45/55 lb.-in.
Torque 15-25 lb.-in.
Apply around and over studs
and nuts Typ (4) pcs.
16
13
4
3
2
21
13
1
6
12
7
14
Apply loctite to stud
prior to asm. with nut
17
16
13
Torque 5-10 lb.-in.
Press Pin (IT5)
Flush with O.D.
with seal (T13)
5
13
9
Nameplate to be
read with B.E. down
30° REF
10
13
Apply loctite (IT 10) under
grommet lip & to lead
exists before applying
sealant
(IT 13)
Black
Shaft Sub Assembly
8 36
23 25
8 22
Orientation Pin
Red
Black
View from plain er.
schematic