manualshive.com logo in svg

Altera timequest, Quick Start Manual

Share
Download
Altera timequest Quick Start Manual Download Page 7

© December 2009 Altera Corporation

TimeQuest Timing Analyzer Quick Start Tutorial

2. Quick Start Tutorial

System Requirements

For this tutorial, use Stratix, Cyclone, MAX II, or newer device families (you can also 
use MAX 3000 and MAX 7000 device families) with the Quartus

®

 II software 

beginning with version 6.0. APEX, FLEX, and Mercury device families are not 
supported.

Procedures

Use the following steps to constrain and analyze a design with the TimeQuest Timing 
Analyzer. Each step includes the GUI procedure and the command-line equivalent.

Step 1: Open and Setup Your Design in the Quartus II Software

In the Quartus II software, browse to and open the 

fir_filter

 located in the 

<

qdesign folder

>

/fir_filter/

 folder. Use the GUI or the command-line equivalent 

procedures in 

Table 2–1

.

Step 2: Setup the TimeQuest Timing Analyzer

By default, the Quartus II software uses the Classic Timing Analyzer as the timing 
analysis tool for designs targeting the Cyclone device family. Specify the TimeQuest 
Timing Analyzer as the timing analysis tool in the Quartus II software to use in the 
compilation flow for the 

fir_filter

 project.

1

This step is not required for all projects. The newer FPGA families default to the 
TimeQuest Timing Analyzer.

Specify the TimeQuest Timing Analyzer as the timing analysis tool in the Quartus II 
software with the procedures in 

Table 2–2

.

Table 2–1.

Opening and Setting Up Your Design

Quartus II Software GUI 

Command Line

On the File menu, click 

Open Project 

and browse to the 

project file <

Quartus II Installation 

Folder

>

\qdesigns\fir_filter\fir_filter.qpf

.

Type:

quartus_sh –s

 

r

project_open fir_filter -revision \ 

filtref

 

r

Summary of Contents for timequest

























Reviews:

No comments

Brands by name

Popular brands

Load more brands