manualshive.com logo in svg

Altera timequest, Quick Start Manual

Share
Download
Altera timequest Quick Start Manual Download Page 14

2–8

Chapter 2: Quick Start Tutorial

Procedures

TimeQuest Timing Analyzer Quick Start Tutorial

© December 2009 Altera Corporation

 

1

This procedure overwrites the previously created 

filtref.sdc

 file. If you overwrite an 

SDC with the

 Write SDC File

 command, your custom formatting and comments are 

removed in the new SDC file. 

The 

filtref.sdc

 file contains the two clock constraints and the false path exceptions. 

Step 11. Perform Timing-Driven Compilation

After saving the constraints to the SDC file, run a full compilation on the design to 
optimize fitting to meet the constraints. However, before you start a full compilation, 
add the SDC to your project with the procedures in 

Table 2–17

.

After you add the SDC to your project, run a full compilation on the design with the 
procedures in 

Table 2–18

.

After compilation is complete, the TimeQuest Timing Analyzer generates a summary 
report of the clock setup and clock hold checks performed in the Compilation Report.

Step 12. Verify Timing in the TimeQuest Timing Analyzer

To obtain detailed timing analysis data on specific paths, view timing analysis results 
in the TimeQuest Timing Analyzer.

1

After a full place-and-route is performed, launch the TimeQuest Timing Analyzer as 
described in 

“Step 4: Launch the TimeQuest Timing Analyzer”

.

Generate a post-fit timing netlist, read the SDC file, and update the timing netlist to 
generate reports about the latest compilation with the procedures in 

Table 2–19

.

Table 2–16.

Saving Constraints to an SDC File 

 TimeQuest Timing Analyzer GUI

 TimeQuest Timing Analyzer Console

1. In the 

Tasks

 pane, double-click 

Write SDC File

. The 

Write 

SDC File

 dialog box appears.

2. In the 

File name

 field, enter 

filtref.sdc

. 

Type: 

write_sdc filtref.sdc

 

r

Table 2–17.

Adding the SDC File to Your Project

 TimeQuest Timing Analyzer GUI

 TimeQuest Timing Analyzer Console

1. On the Project menu, click 

Add/Remove Files In Project

. 

The 

Add/Remove Files In Project

 dialog box appears.

2. Browse to and select the 

.sdc

.

3. Click 

OK

.

Type: 

set_global_assignment -name SDC_FILE \ 

filtref.sdc

 

r

Table 2–18.

Running a Full Compilation

 TimeQuest Timing Analyzer GUI

 TimeQuest Timing Analyzer Console

On the Processing menu, click 

Start Compilation

.

Type: 

quartus_sh  --flow compile filtref

 

r

Summary of Contents for timequest

























Reviews:

No comments

Brands by name

Popular brands

Load more brands