Altera JESD204B IP CORE Page 64 User Manual Download

Page: 64 / 158

Transmitter

Table 4-5: Transmitter Signals

Signal

Width

Direction

Description

Clocks and Resets

pll_ref_clk

Input

Transceiver reference clock signal. The

reference clock selection depends on the

FPGA device family and data rate.
This signal is only applicable for V series

FPGA variants.

txlink_clk

Input

TX link clock signal. This clock is equal to the

TX data rate divided by 40. This clock must

have the same frequency as the

txphy_clk

signal but can be differential in phase due to a

different clock network.
For Subclass 1, you cannot use the output of

txphy_clk

signal as

txlink_clk

signal . To

sample

SYSREF

correctly, the core PLL must

provide the

txlink_clk

signal and must be

configured as normal operating mode.

txlink_rst_n_reset_n

Input

Reset for the TX link clock signal. This reset is

an active low signal.

txphy_clk[]

Output

TX parallel clock output for the TX PCS. This

clock must have the same frequency as

txlink_clk

signal.

This clock is output as an optional port for

user if the

txlink_clk

and

txframe_clk

signals are operating at the same frequency in

Subclass 0 operating mode.

tx_digitalreset[]

(22)

Input

Reset for the transceiver PCS block. This reset

is an active high signal.

tx_analogreset[]

(22)

Input

Reset for the transceiver PMA block. This

reset is an active high signal.

(22)

The Transceiver PHY Reset Controller IP Core controls this signal.

UG-01142

2015.05.04

Transmitter

4-27

JESD204B IP Core Functional Description

Altera Corporation

Send Feedback

Summary of Contents for JESD204B IP CORE































































































































































Search results

Summary of Contents for JESD204B IP CORE

Reviews:

Related manuals for JESD204B IP CORE

Brands by name

Popular brands

Altera JESD204B IP CORE, User Manual

Search results

Summary of Contents for JESD204B IP CORE

Reviews:

Related manuals for JESD204B IP CORE

Brands by name

Popular brands