Altera JESD204B IP CORE Page 76 User Manual Download

Page: 76 / 158

Signal

Width

Direction

Description

jesd204_rx_avs_clk

Input

The Avalon-MM interface clock signal. This clock

is asynchronous to all the functional clocks in the

JESD204B IP core. The JESD204B IP core can

handle any cross clock ratio and therefore the

clock frequency can range from 75 MHz to 125

MHz.

jesd204_rx_avs_rst_n

Input

This reset is associated with the

jesd204_rx_avs_

clk

signal. This reset is an active low signal. You

can assert this reset signal asynchronously but

must deassert it synchronously to the

jesd204_

rx_avs_clk

signal. After you deassert this signal,

the CPU can configure the CSRs.

jesd204_rx_avs_

chipselect

Input

When this signal is present, the slave port ignores

all Avalon-MM signals unless this signal is

asserted. This signal must be used in combination

with read or write. If the Avalon-MM bus does not

support chip select, you are recommended to tie

this port to 1.

jesd204_rx_avs_

address[]

Input

For Avalon-MM slave, the interconnect translates

the byte address into a word address in the address

space so that each slave access is for a word of data.

For example, address = 0 selects the first word of

the slave and address = 1 selects the second word

of the slave.

jesd204_rx_avs_

writedata[]

Input

32-bit data for write transfers. The width of this

signal and the

jesd204_rx_avs_readdata[31:0]

signal must be the same if both signals are present.

jesd204_rx_avs_read

Input

This signal is asserted to indicate a read transfer.

This is an active high signal and requires the

jesd204_rx_avs_readdata[31:0]

signal to be in

use.

jesd204_rx_avs_write

Input

This signal is asserted to indicate a write transfer.

This is an active high signal and requires the

jesd204_rx_avs_writedata[31:0]

signal to be

in use.

jesd204_rx_avs_

readdata[]

Output

32-bit data driven from the Avalon-MM slave to

master in response to a read transfer.

UG-01142

2015.05.04

Receiver

4-39

JESD204B IP Core Functional Description

Altera Corporation

Send Feedback

Summary of Contents for JESD204B IP CORE































































































































































Search results

Summary of Contents for JESD204B IP CORE

Reviews:

Related manuals for JESD204B IP CORE

Brands by name

Popular brands

Altera JESD204B IP CORE, User Manual

Search results

Summary of Contents for JESD204B IP CORE

Reviews:

Related manuals for JESD204B IP CORE

Brands by name

Popular brands