Altera JESD204B IP CORE Page 107 User Manual Download

Page: 107 / 158

Parameter

Description

Value

F2_FRAMECLK_DIV Only applies to cases where F=2.

The divider ratio on the

frame_clk

. The deassembler always uses the

post-divided frame_clk (rxframe_clk).

(34)

1, 2

RECONFIG_EN

Enable reconfiguration support in the transport layer. Only

downscaling reconfiguration is supported. Disable the reconfigura‐

tion to reduce the logic.

0, 1

OUTPUT_BUS_

WIDTH

The data output bus width size that depends on the F and L.
bus_width = M*S*N
F = (M*S*N_PRIME)/(8*L)
M*S = (8*F*L)/N_PRIME
Therefore the output bus width = (8*F*L*N)/N_PRIME

(8*F*L*

N)/N_

PRIME

CONTROL_BUS_

WIDTH

The control output bus width size. The width depends on the CS

parameter as well as the M and S parameters. When CS is 0, the

control data is one bit wide (tie the signal to 0).
If CS = 0, the bus width = 1. Otherwise, the bus width = (OUTPUT_

BUS_WIDTH/N*CS) while OUTPUT_BUS_WIDTH/N = M*S

OUTPU

T_BUS_

WIDTH/

N*CS

Table 5-12: Deassembler Signals

Signal

Clock Domain

Direction

Description

Control Unit

rxlink_clk

—

Input

RX link clock signal. This clock is equal to the RX

data rate divided by 40. This clock is synchronous

to the

rxframe_clk

signal.

rxframe_clk

—

Input

RX frame clock used by the deassembler. The

frequency is a function of parameters

F1_

FRAMECLK_DIV, F2_FRAMECLK_DIV

and

rxlink_clk

This clock is synchronous to the

rxlink_clk

signal.

rxlink_rst_n

rxlink_clk

Input

Reset for the RX link clock domain logic in the

deassembler. This reset is an active low signal and

the deassertion is synchronous to the rising-edge

rxlink_clk

rxframe_rst_n

rxframe_clk

Input

Reset for the RX frame clock domain logic in the

deassembler. This reset is an active low signal and

the deassertion is synchronous to the rising-edge

rxframe_clk

5-26

RX Path

UG-01142

2015.05.04

Altera Corporation

JESD204B IP Core Design Guidelines

Send Feedback

Summary of Contents for JESD204B IP CORE































































































































































Search results

Summary of Contents for JESD204B IP CORE

Reviews:

Related manuals for JESD204B IP CORE

Brands by name

Popular brands

Altera JESD204B IP CORE, User Manual

Search results

Summary of Contents for JESD204B IP CORE

Reviews:

Related manuals for JESD204B IP CORE

Brands by name

Popular brands