6
Remote Control
1
STANDBY/ON key
Turns on the M812 or places it in
standby mode.
2
MUTE
Mutes the speaker.
3
MASTER VOL +/– keys
Press to adjust the volume of
several speakers when they are all
synchronized with the transmitter
base. If you have only one speaker,
these keys operate the same as +/–
keys on the ring of controls on the
lower part of the remote and the
volume controls on the side of
the M812.
4
BASS +/– keys
Adjusts the bass tones of the speaker
up or down from -6 to +6 decibels.
5
/– keys
Adjusts the treble tones of the speaker
up or down from -6 to +6 decibels.
6
iPOD/FM/AUX keys
Press to select an input source.
7
1–6 keys
Used to select and set FM station
presets.
To preset an FM station:
• Tune to the desired FM station.
• Press one of the preset keys for
three seconds. The display will
show PRESET and the number of
the preset key.
8
+/– keys
Controls the volume of the M812 at which you are pointing
the remote.
(FR/FF) keys
For iPod and AUX inputs:
• Press once to move to the previous or next track of IPOD or
AUX inputs.
• Press and hold the key down to do a fast forward or rewind.
FM tuning:
• Press once to tune to the next station.
• Hold the key for a second to get SEEK mode where you tune to the
next station with a clear signal.
• Hold for two seconds to get a SCAN mode which cycles through
each channel until you release the key.
9
(Play/Pause) key
Press to play or pause the playback of IPOD or AUX inputs. Toggles
between play and pause modes each time it is pressed.
Placement of the M812’s Wireless Speaker
and Transmitter Base
The transmitter base can be placed on a suitable level surface within
reach of an electrical outlet.
NOTE:
If you plan to use the FM receiver function of the M812 you
should place the transmitter base where the supplied FM antenna can
be located for best reception.
The wireless speaker can be placed on a suitable level surface or
mounted on the wall using the supplied wall mounting bracket. When
placing the wireless speaker on a level surface it is necessary to use the
base that is preinstalled on the unit.
NOTE:
Placement of this product on wood surfaces with certain types
of finishes, such as clear varnish, may result in damage to the finish.
Consult the furniture manufacturer’s care instructions for direction as
to the types of objects that may safely be placed on the wood surface.
Altec Lansing shall not be responsible for any damage to wood surfaces
from contact with this product.
Caution:
The wall-mounting bracket should be installed only by
qualified personnel. The mounting plate can be installed on many
different types of walls. When installed, the mounting plate must
support at least 60 lbs. The installer must be sure that the installing
surface can support the 60 lb. weight requirement. The qualified
installer must also determine and use the proper hardware to obtain
the weight requirements for the wall.
If you are mounting the M812 on the wall please follow these steps:
1. Remove the base from the bottom of the wireless speaker.
2. Determine a suitable wall location for mounting the wireless speaker
that includes an AC outlet within reach of the unit’s AC cord.
. Position and level the supplied metal mounting bracket in the
desired location on the wall.
4. Being careful to avoid any items (wires, pipes, etc.) hidden inside the
wall, secure the metal mounting bracket using appropriate fasteners
for the application. If you are unsure which type of fasteners to use
or are unable to determine if there are items within the wall that
could be damaged, please consult a licensed contractor.
5. Place the speaker on the mounting bracket by aligning the two
keyholes on the rear of the speaker with the posts on the mounting
bracket. Check to make sure the wall mount bracket and speaker are
securely fixed in place.
Connect M812 System Components
Transmitter Base and iPod Dock
The M812 supports a variety of iPods, including the iPod nano, iPod
video, iPod with color display, iPod mini and iPod. To use an iPod with
the M812, install the appropriate adapter plate into the universal dock.
You can use one of the black adapters supplied or, if the correct black
adapter is not supplied, one of the adapters supplied with your iPod or
available from Apple.
NOTE: UPGRADING iPOD SOFTWARE
If the iPod does not function or respond properly when docked into the
transmitter base, you may need to update the software on your iPod to
ensure optimal playback performance and proper operation.
Go to the Apple website and follow the directions to upgrade your iPod
to the latest software.
8
9
7
6
5
4
3
2
1
