background image

15

Toilet will be left unused for > 3 weeks

When the product is left unused for a 

long time, especially in cold weather, it 

is highly recommended to drain the 

water to prevent freezing.

To discharge water

1. Activate flushing, and then turn off the

angle valve to stop water supply.

2. Unplug the power cord
3. Disconnect the hose from angle

valve, drain the water and

reconnect.

Note

Be sure to unplug the power cord

before disconnecting the 

supply hose. 

* Please turn on power and water supply when

using again.

Backup battery replacement 

1. Unplug DC connector and remove the

battery box.

2. Install a new 9V battery.
3. Reconnect the battery box.

Reminder:

1. It is recommended to use high quality

6LR61 9V battery.

2. It is recommended to replace the battery

every two years, regardless of use.

battery

Failure of remote control

Note: After battery replacement, the remote 

control settings will be reset to the defaults. 

User presets will need to be re-saved. 

1. Operate via knob on the main unit.

2. Battery replacement

Remove the remote control from

holder.

Open the battery cover and replace

the batteries.

Put the remote control back.

Summary of Contents for UX-T Pearl





















Reviews: